Filter
Top Products
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
Carpet Height Selector
This upright vacuum can be used on
multiple types of carpeting, bare floors
or upholstery with attachments.
To select a pile height setting:
1. Turn vacuum cleaner "Off".
2. Select a pile height setting by
sliding the carpet height selector
to the desired setting. (Fig. 4)
Removing & Emptying Dust Cup
HIGH: shag carpet, long pile,
plush scatter rugs, tools
MED: medium to long pile
LOW: short to medium pile,
bare floors
FLOOR: very low pile, bare
floors
Suggested Pile Height Setting:
You may need to raise the height of the
vacuum to make some jobs easier,
such as scatter rugs and longer pile
carpets. Suggested settings are:
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, dust cup filter,changing the filters or
performing maintenance/trouble shooting
checks.
The “Dust Cup” must always be emptied
when the dirt level reaches the "FULL"
line on the dust cup. To remove the dust
cup from the vacuum:
1. Press down on the dust cup
release button that is located on
the handle of the dust cup.
(Fig. 6)
2. Holding the dust cup from the
handle, pull the dust cup out
from the vacuum. (Fig. 7)
3. To empty the dust cup, hold it by
the handle over a garbage can
and press on the trap door
release button to empty. (Fig. 8)
Fig. 4
Fig. 6 Fig. 7
Fig. 8
5
Place unit in "HIGH" setting when using
attachments to prevent possible floor
damage. Always set the Carpet to Floor
selector to “Floor” setting when using
the accessories. (Fig. 5)
Attention: Special care is required
when vacuuming certain types of carpet
or floor covering. Always check the
carpet or floor covering manufacturer's
recommended cleaning instructions
before vacuuming.
Trap Door
Release
Fig. 5
Cleaning the HEPA Filter Frame
1. Before replacing the HEPA filter in the
HEPA Filter frame, you can (should)
rinse the frame in lukewarm water by
just running it under the tap to remove
any dust that is adhering to the frame.
(Fig. 13) Do NOT place in dishwasher.
Fig. 13
2. Make sure that the filter frame is
completely dry before replacing into
the dust cup. Always air dry for 24
hours.
Fig. 9
Fig. 12
1. To remove the HEPA
filter, remove the dust cup from the
unit.
2. To remove the dust cup
cover, hold the cover by
the handle, turn counter
clockwise and lift the
cover off. (Fig. 9)
3. Remove the HEPA
Rinseable "Tap Clean"
filter from the dust cup.
(Fig. 10)
4. Vigorously "TapClean"
the HEPA dust cup
filter on a hard
surface until no
more dust is
observed falling
out. (Fig. 11)
The HEPA filter may
also be washed by
running it under the
tap allowing the water
to run on the dirty side.
(Fig. 12) We
recommend washing
it once a month
or when suction appears
reduced. Always allow 24
hours for air drying before
replacing into the vacuum.
Fig. 10
Cleaning the Secondary Filter
1. Underneath the HEPA
filter there is a
secondary filter.
This is washable in
lukewarm water.
(Fig. 14) We
recommend washing
it when you are
washing your HEPA filter.
Always allow the secondary
filter to air dry for 24 hours
before replacing into the
vacuum. Never run
the vacuum without
the secondary filter in place.
Fig. 14
Please Note: The white material in the
HEPA filter will discolor over time - This is
NORMAL and will NOT affect the
performance of the filter.
IMPORTANT, Please Note : The Rinseable
“TapClean” HEPA Dust Cup Filter will stop
most of the tiniest dust particles and
airborne allergens from re-entering the air
you breathe. In fact, it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!! Because
of this incredible filtration performance, the
HEPA Dust Cup Filter will quickly
accumulate many fine dust particles inside
the white filter folds that are difficult to see
but which will eventually block or reduce
your suction power - if not cleaned properly.
Clean the HEPA Filter after each use as
described in this section.
Cleaning the HEPA Dust Cup Filter
Warning: Always empty the dust cup
and clean the HEPA dust cup filter
before each use and during prolonged
usage. Never over fill the dust cup -
remove dirt and clean the HEPA dust
cup filter each time the dust cup is
emptied during prolonged usage or risk
motor damage.
Fig. 11
6