Filter
Top Products
Check both electrostatic
filters whenever the bin is
emptied and replace at
least every 3 months.
Please note that if the filters are not checked regularly and changed
as required, the motor may overheat, which will cause the thermal
cut-out to operate.
NOTE: Vacuuming builder’s dust and some carpet fresheners may
cause the filters to require changing more frequently. (Dyson
does not recommend the use of carpet fresheners).
Replacement filters are available from your local retailer or
direct from Dyson. Call or fax the Helpline for orders.
IMPORTANT: Use only genuine Dyson filters, which
have been tested and approved for this cleaner.
Your Dyson has a built-in thermal cut-out to protect it in the
event of a restriction to the airflow and may suddenly stop
working temporarily if you do not change the filters at the
stated time, or if blockages are not cleared immediately.
If the vacuum cleaner suddenly stops working (ie. the motor makes no
sound when switched on) then please check your cleaner for blockages as
detailed in this operating manual. (Remember also to check the fuse in the
plug). Having established that there are no blockages and that the filters
have been replaced within the stated time, leave your vacuum cleaner
unplugged for 60 minutes and then try using it again.
If the vacuum cleaner still does not work, please call Dyson
Customer Care (Tel: 01666 827272).
DYSON CUSTOMER CARE
TETBURY HILL
MALMESBURY
WILTSHIRE
ENGLAND
SN16 ORP
Important
Helpline 01666 827272
Facsimile 01666 827298
Contact for all service assistance
Check that your supply corresponds to that shown on the rating plate. The appliance must
only be used as rated, it should be fitted with an ASTA approved fuse to BS1362.
European conformity information A sample of this product has been tested and found
to be in conformity with the following European Directives: 73/23/EEC Low voltage (safety)
Directive, 93/68/EEC CE Marketing Directive and 89/336/EEC EMC Directive.
For your convenience this appliance is supplied with a plug which is fitted with a 13amp
fuse of the appropriate rating.
Never put the plug into the socket outlet without the fuse cover fitted. Replacement fuse
covers are available from Dyson Customer Care. If the plug supplied is not suitable for
your socket outlet, it should be cut off and destroyed/safely disposed of. Warning: Under
no circumstances should the severed plug be inserted into a 13A socket, serious
danger of electric shock would result from the exposed wires.
The mains lead can then be shortened to the minimum required length, suitably prepared
and the correct style of plug to suit your household wiring system should be fitted. The
following wiring instructions should be followed. If in doubt, consult a qualified
electrician.
Unwanted products and the environment Should you find that your product needs
replacing one day, or is of no further use to you, think of protecting the environment. Dyson
will accept your old products and recycle them in an environmentally friendly way.
The wires in the mains lead are coloured in accordance with the following codes.
Brown – Live
Blue – Neutral
As the colours of the wires in the mains lead may not correspond with the colours or
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured Blue must be connected to the terminal which is marked with
the letter N or coloured Black.
The wire that is coloured Brown must be connected to the terminal which is marked with
the letter L or coloured Red.
Neither wire should be connected to the earth terminal of a three pin plug which is marked
with the letter E or or coloured Green or Green and Yellow.
Always ensure that the cable clamp is fitted and that it clamps the cable outer and NOT
the coloured wires.
If the supply cord of the appliance is damaged, disconnect the appliance from the socket
outlet immediately. The supply cord must be replaced and only by Dyson Appliances Ltd.
or their appointed agent as special purpose tools and service techniques are required.
IMPORTANTNOTE
IMPORTANT
ALWAYS UNPLUG THE VACUUM CLEANER FROM THE WALL SOCKET BEFORE INSPECTING IT
NOTE
S-Level
S
3