Filter
Top Products
.
(iii) Take extra care when vacuuming on stairs; do not work with the vacuum cleaner above you
on the stairs. Do not put the vacuum cleaner on chairs, tables etc.
(iv) Ensure machine is in upright position before using tools.
To release the wand, open the wand cap and pull the red tube until the wand releases from the
vacuum. Tools can be attached to either the hose or wand.
The brushbar will not rotate when the machine is in an upright position.
Ensure wand cap is closed when not in use.
Emptying the Clear bin
TM
Caution:
(i) Switch ‘OFF’ machine and unplug before emptying the bin.
Empty as soon as the dirt reaches the level of the MAX mark – do not overll. To remove the
clear bin
TM
from the machine press the button at rear of cyclone carrying handle. To release the
dirt, press the red bin release button.
Please note:
(i) Do not use the machine without the clear bin
TM
in place.
Cleaning the Clear bin
TM
Caution:
(i) Do not immerse the whole cyclone in water or pour water into the cyclones.
(ii) Ensure bin is completely dry before replacing.
Please note:
(i) Do not use detergents, polishes or air fresheners to clean the bin.
(ii) Do not put bin in a dishwasher.
Washing your lters
Caution:
(i) Switch ‘OFF’ and unplug machine before removing the lters.
(ii) Ensure lters are completely dry before retting to machine.
This machine has two lters, located as shown. It is important to check your lters regularly and
wash at least every 3 months according to instructions, to maintain performance. The lter in the
ball should be rinsed and tapped out until the water runs clean, then tapped out again to ensure
all excess water is removed. This will normally require up to 10 rinse cycles. Please leave to dry
completely for 24 hours.
Please note:
(i) It is normal for this lter in the ball to turn grey in color. The lters may require more
frequent washing if vacuuming ne dust.
(ii) Do not use detergents to clean the lters.
(iii) Do not put the lters in the dishwasher, washing machine, tumble dryer, oven, microwave
or near an open ame.
Looking for blockages
Caution:
(i) Switch ‘OFF’ and unplug machine before checking for blockages. Failure to do so could
result in personal injury.
(ii) Please ensure machine is upright and switched off before removing hose or airway
inspection parts.
(iii) Beware of sharp objects when clearing blockages.
(iv) Ret all parts of the machine securely before using.
Please note:
(i) Clearing blockages is not covered by your machine’s limited warranty. This machine is tted
with a thermal cut-out. If any part of your machine becomes blocked, it may overheat and then
automatically shut off. Switch ‘OFF’ and unplug machine and leave to cool down for at least
60 minutes before attempting to check lters or for blockages. Clear blockage before restarting.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
Assembly
Lie machine at and attach cleaner head by sliding it on until it clicks.
Stand vacuum cleaner up straight, attach wand to hose and push into place until it clicks.
Push wand down into hose and attach tools to the side of the machine.
Using your Dyson
Press foot pedal and recline handle to use. The stabilizer stand will automatically lift up.
To switch ‘ON’, depress power button in front of handle. When nished cleaning, push machine
into an upright position and stabilizer wheels will automatically drop. Use the cyclone carry handle
to carry the machine.
Caution:
(i) If the vacuum cleaner is not functioning properly, has been dropped, damaged, left outdoors,
or immersed in liquid, contact the Dyson helpline.
(ii) Do not allow the vacuum cleaner to be used by anyone who may not be able to operate it safely.
(iii) The use of an extension cord is not recommended.
(iv) Always switch off and unplug before performing maintenance on your appliance.
(v) When returning to the upright position, ensure that the stabilizer wheels are fully engaged before
releasing the cleaner.
(vi) Ensure the cyclone is secured to the machine. Do not press the cyclone release button or shake
the appliance while carrying or it could fall and cause injury.
(vii) Store the machine indoors. Put the vacuum cleaner away after use with the cable coiled safely,
to prevent tripping hazards.
(viii) Do not use your vacuum cleaner outdoors or on wet surfaces. Vacuum may be used inside a
garage only when used with the Model 08909 Dyson Car Cleaning Kit accessories. If used in a
garage, care should be taken to wipe the soleplate and wheels with a dry cloth after vacuuming
to clean off any sand, dirt, or pebbles that could damage delicate oors.
(ix) Do not use outdoors or on wet surfaces or to vacuum water or other liquids – electric shock could occur.
(x) Check to ensure your electricity supply corresponds to that shown on the rating plate, which can
be found behind the clear
bin.
TM
The machine must only be used as rated.
(xi) Do not
lubricate any parts, or carry out any maintenance or repair work other than that shown
in this manual, or advised by the Dyson Helpline.
Please note:
• This machine is intended for domestic use only. Fine dust such as plaster dust or our should only
be vacuumed in very small amounts.
• Do not use the machine to pick up sharp hard objects, small toys, pins, paper clips, etc. They may
damage the machine.
• When vacuuming, certain carpets may generate small static charges in the clear bin
TM
or wand.
These are entirely harmless and are not associated with the electricity supply. To minimize any effect
from this, do not put your hand or insert any object into the clear bin unless you have rst emptied
it and rinsed it out with cold water.
• Consult your ooring manufacturer’s recommended instructions before vacuuming and caring for
your ooring, rugs, and carpet. Some carpets will fuzz if a rotating brushbar is used when
vacuuming. If this happens, we recommend vacuuming in bare oors mode and consulting with
your ooring manufacturer.
Hard oors or carpets
The brushbar will always default to ‘ON’ (spinning) each time you switch on the machine and recline
it for cleaning. The brushbar will automatically stop if it becomes obstructed. If the brushbar stops
during use, please refer to the ‘Clearing brushbar obstructions’ section.
To switch the brushbar off (e.g. for hard oors), recline the machine and turn it ‘ON’, then press the
brushbar ‘ON/OFF’ button – the brushbar will stop spinning.
Using the tools – High-reach cleaning
Caution:
(i) Switch ‘OFF’ machine before changing tools.
(ii) Powerful suction can cause the hose to ‘pull back’ - please take care.