Dimplex EN55014 Stove User Manual


 
- 3 -
Battery Information.
1. Unclip the battery cover on the back of the remote
control. (See Fig. 7)
2. Install AAA batteries into the remote control.
3. Replace the battery cover.
Discard leaky batteries.
Dispose of batteries in the proper manner according to
provincial and local regulations.
Any battery may leak electrolyte if mixed with a di erent
battery type, if inserted incorrectly, if all the batteries are
not replaced at the same time, if disposed of in a  re, or if
an attempt is made to charge a battery not intended to be
recharged.
Thermal safety cut-out
A thermal safety cut-out is incorporated in the fan stove
to prevent damage due to overheating. This can happen if
the heat outlet was restricted in any way or if the chimney
ue has not been blocked o e ectively. If the cut-out
operates, unplug the stove from the socket outlet and
allow approximately 10 minutes before reconnecting.
Before switching the stove back on remove any
obstruction that may be restricting the heat outlet, then
continue normal operation.
Tips for using your appliance.
1. Only pull out the drawer when its time to re ll the
water tank or change a lamp, otherwise it may lead to
excess water in the sump and reduced  ame e ect.
If this happens empty the water from the sump as
instructed under ‘Maintenance’.
2. With the  ame setting on minimum the unit will use
approximately 40ml of water per hour and will last
3 times as long than when it is at maximum  ame
setting.
3. Do not tilt or move the stove while there is water in the
tank or sump.
4. Make sure that the stove is on a level  oor.
5. The ame control knob ‘C’ Fig. 2 may be turned up or
down to give a more realistic e ect.
6. Sometimes the  ames appear more real when the
ame control knob is turned down.
7. Give the  ame generator some time to react to
changes you may make on the  ame control knob.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE
Changing lamps.
If a large amount of the smoke appears grey or colourless
it may be that one or more lamps have failed.
You can check for lamp failure as follows.
1. Leaving the  ame e ect on, open the doors fully,
gently pull the drawer fully out by the tab. (See Fig. 3)
2. View the lamps from a distance in front of the stove
and observe which lamp needs to be changed.
3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the stove
from the mains.
4. Leave the appliance for 20 minutes to allow the lamps
to cool down before removing them.
5. Remove the water tank by lifting upwards and place in
a sink.
6. Remove the sump as described in the Cleaning Section.
7. Remove the defective lamp, by gently lifting vertically
and disengaging the pins from the lamp holder, (See
Fig. 4 and 5). Replace with a Dimplex Opti-myst, 12V,
50W, Gu5.3 base, 8° beam angle, coloured lamp.
(Purchased from www.dimplex.co.uk under the section
‘After Sales Service’, details of how to purchase the
lamps are contained therein.)
8. Carefully insert the two pins of the new lamp into the
two holes in the lamp holder. Push  rmly in place. (See
Fig. 4 and 5).
9. Replace the Sump and water tank and carefully close
the drawer and doors.
10. Switch on.
Filling the water tank.
When the water tank is empty,  ame and smoke e ect
shuts o , and you will hear 2 audible ‘beeps’. Follow these
steps to re ll:
1. Open doors.
2. Press Switch ‘A’ to (0) (See Fig. 2).
3. Open the doors fully and gently pull out the drawer as
far as possible by the tab. (See Fig. 3)
4. Remove the water tank by lifting upwards and
outwards.
5. Place the water tank in sink and remove cap, Anti-
clockwise to open. (See Fig. 6)
6. Fill tank with  ltered tap water only. This is necessary
to prolong the life of the  ame and smoke producing
unit.
The water should be  ltered through a conventional
domestic water  lter unit and the  lter should be
replaced regularly.
7. Screw the cap back on, do not overtighten.
8. Return the tank to the sump, with the tank cap facing
down and the  at side of the tank facing outward.
9. Gently push the drawer back in as far as it will go.
10. Press Switch ‘A’ to ‘ON’ ( I ) position (See Fig. 2)
11. Press Switch ‘B’ once to turn on  ame e ect. (See
manual control section and Fig. 2)