Filter
Top Products
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical
shock, and injury to persons, including the following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower
or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover the heater. Do not place material or garments
on the heater, or obstruct the air circulation around the
heater, for instance by curtains or furniture, as this could
cause overheating and a fire risk.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they
do not play with the appliance.
Do not use this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
Caution: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not
be supplied through an external switching device, such as
a timer, or connected to a circuit that is regularly switched
on and off by the utility.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
General
Unpack the heater carefully and retain the packaging for possible future
use, in the event of moving or returning the fire to your supplier. The
Remote Control and batteries are packed separately in the carton.
Loose coals are also packed separately within the carton. When the
heater is assembled the coals are placed on top of the fuel bed.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires little electricity.
The heater is designed for use inset into a 407mm (16") or 457mm (18")
wide by 559mm (22") high fireplace opening or freestanding - see also
section ‘Installation in a fire place opening’.
Before connecting the heater check that the supply voltage is the same
as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for
concern.
Installation in a Fireplace Opening
At the rear of the fire, two adjustable feet are provided for levelling the
fire where the base of the fireplace opening is raised above the level
of the hearth.
Adjust the foot by rotating it to the required position.
The metal surround may be removed (six screws) to allow the fire to
be fully inset as indicated in Fig. 2B. The minimum opening size required
for the fire to be fully inset is *392mm wide, *550mm high and *70mm
deep - see Fig. 1. Alternatively the metal surround may be left on and
positioned freestanding against a wall as indicated in Fig. 2A.
To ensure the appliance stability, the fire is supplied with a hook and
rawl plug. The rawl plug supplied is suitable for use in block walls
(special fasteners required on stud walls).
Spacer attached - Fig. 3A: In the event that the fire is to be positioned
against a wall with the metal spacer attached, the fixing position of the
hook is indicated by ‘X’ in Fig. 3A. When the hook is securely fastened,
centre the fire to the hook. Lift the fire up and over the hook (see ‘z’ in
Fig. 4) ensuring that the surround (see ‘w’ in Fig. 4) engages the hook.
No Spacer attached - Fig. 3B: In the event that the fire is to be
positioned fully inset without the metal spacer, the fixing position of the
hook is indicated by ‘Y’ (the hook can be positioned on either side of
the fire) in Fig. 3B. When the hook is securely fastened, position the
top outer slot on the fire (see Fig. 3B) alongside the hook, lift the fire up
and over the hook so that the top outer slot on the fire engages the
hook.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
Instructions.
Controls - see Fig. 6
The product can be controlled both manually and by remote control.
Manual Controls
The fire controls are located at the base of the fire behind the bottom
fret - see Fig. 5.
To gain access to controls, remove fret by pulling outwards using fret
knob. Two switches and a thermostat knob provide a choice of fire
settings see Fig. 6. The red indicator mark on the switch will be visible
when it is turned on.
Switch B Controls the electricity supply to the heater.
Note: This switch must be in the ON position for the heater to operate
with or without heat.
Switch A Controls the function of the fire.
Press once to give flame effect only.
Press again to give heat and flame effect.
Press again to go back to flame effect only.
Pressing ‘O’ at any stage turns the fire to standby mode.
Note: To turn fire completely off use switch B.
Thermostat
In order to maintain a certain room temperature, set the controller to
‘max.’. Operate the appliance at full power until the required room
temperature is reached. Set back the thermostatic controller until the
appliance switches off. This temperature will be kept almost constant
by the thermostatic control switching on and off automatically.Please
note that the appliance can only be switched on when the thermostat
setting is higher then the room temperature.
Initializing the Remote Control
Note: The remote control is packed separately in the carton.
1. Slide open the battery cover on the back of the remote
transmitter.
2. Install the AAA batteries into the remote control (see
Fig. 9).
3. Replace battery cover.
Dispose of batteries in the proper manner according to Provincial and
local regulations. Any battery may leak electrolyte if mixed with a different
battery type, if inserted incorrectly, if all the batteries are not replaced
at the same time, if disposed of in a fire or if an attempt is made to
charge a battery not intended to be recharged.