Filter
Top Products
108861-01D
For more information, visit www.desatech.com
For more information, visit www.desatech.com
27
27
OPERATING FIREPLACE
Continued
IMPORTANT:
This remote control has been specially
engineered to take an air temperature sample every 5.5
minutes in the auto mode. It will not respond immedi-
ately to the temperature setting being turned up or down.
IMPORTANT:
The hand-held remote control unit must
be near the heater. Do not keep the hand-held remote
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the heater off.
3. To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT:
To turn the pilot off, manually turn the con-
trol knob on the heater to the OFF position.
1. After lighting, let pilot flame burn for about one minute. Turn
gas control knob to ON position. Adjust variable control knob
anywhere between HI and LO. Slide the selector switch to the
REMOTE position (see Figure 53).
Note:
The burners may
light if hand-held remote ON button was on when selector
switch was last turned off. You can now turn the burners on
and off with the hand-held remote control unit.
IMPORTANT
: Do not leave the selector switch in the RE-
MOTE position when the pilot is not lit. This will drain the
battery.
IMPORTANT:
Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
(C)GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
(C)GHRCT(A) Series Operation:
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 54). The lights to the left of the button
will show AUTO, ON, or OFF.
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See
Lighting Instruc-
tions
on page 26.
OPTIONAL REMOTE OPERATION
Note:
All remote control accessories must be purchased sepa-
rately (see Accessories, pages 42 and 43). Follow instructions
included with the remote control.
(Optional [C]GHRCT[A] Only) The thermostat control setting
on the remote control unit can be set to any comfort level
between HI and LO. The burners will turn on and off automati-
cally to maintain the comfort level you select. The ideal comfort
setting will vary by household depending upon the amount of
space to be heated, the output of the central heating system, etc.
OPERATING FIREPLACE
Optional Remote Operation
O
F
F
P
I
L
O
T
O
N
L
O
I
H
ON
OFF
REMOTE
ON
OFF
Blower Control Knob
(Optional Accessory)
Variable
Control Knob
Selector Switch in
Remote Position
Gas Control Knob
in ON Position
Figure 53 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
Figure 54 - Thermostat Hand-Held Remote Control Unit Selections
([C]GHRCT[A] Series Only)
Increases Room
Temperature in
AUTO Mode
Decreases Room
Temperature in
AUTO Mode
Turns Burners On
or Off and Allows
You to Choose the
Auto Setting
Shows
Temperature
Setting
The Log Heater
will Automatically
Cycle between
Pilot and the Heat
Setting that has
been Selected