Filter
Top Products
SPECIFICATIONS………………………. 2
INTRODUCTION……………………….. 3
VENTING………………………………... 3 ,4
GAS SUPPLY……………………………. 5
LOCATION & SPECIAL PRECAUTIONS 5
COMBUSTION & VENTILATION AIR.... 6
CLEARANCES………………………….. 7
DRAFT DIVERTER…………………….. 7
DOOR KNOB…………………………… 7
PILOT ADJUSTMENT…………………. 8
RADIANTS & GLASS PANELS……….. 8
BURNER ORIFICE & ORIFICE CHART.......... 8
PROPER BURNER FLAME.............…………. 9
MAINTENANCE…………………………....... 9
LIGHTING INSTRUCTIONS……………........ 10
TROUBLE SHOOTING CHART………… 11,12
BLOWER INSTRUCTIONS……………… 13
TSK WALL STAT KIT................................ 14
PARTS DRAWING……………………….. 15
PARTS PRICE LIST………………………. 16
WARRANTY……………………………… 18
READ CAREFULLY BEFORE INSTALLING UNIT
These installation instructions are a general guide and do not supersede applicable local codes and ordinances. Before
planning or making the installation be sure it complies with all phases of the local heating code. (Or, in the absence of
local codes, with the latest edition of National Fuel Gas Code, ANSI.Z223.1, or CAN1-B149).
The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local
codes, with the latest edition of National Electrical Code ANSI/NFPA 70, or Canadian Electrical Code CSA-C22.1.
All of the ANSI and NFPA standards referred to in these installation instructions are the ones that were applicable at
the time the design of this appliance was certified. The ANSI standards are available from the American Gas Association,
1515 Wilson Blvd., Arlington, VA. 22209.
The NFPA standards are available from the national Fire Protection Association, 60 Batterymarch Street, Boston,
Massachusetts 02110.
Canadian standards are available from International Approval Services, 178 Rexdale Boulevard, Etobicoke, Ontario,
Canada M9W 1R3.
The design of this appliance was certified to comply with ANSI Z21.11.1 vented room heaters and CAN1-2.1-M86.
Installer must leave these instructions with the consumer, have them complete, and return the warranty card.
ROOM HEATER SPECIFICATIONS
Your room heater comes packed in a single carton. Before installation, check the rating plate to verify that the Model Number is
correct and that the room heater is equipped for the type gas you intend to use.
TABLE OF CONTENTS
TYPE CONTROL GAS MODEL NUMBERS
CLOSED FRONT THERMOSTAT BULB NATURAL VC201A-H VC351A-H VC501A-H VC701A-H
CLOSED FRONT THERMOSTAT BULB L.P. VC202A-H VC352A-H VC502A-H VC702A-H
RADIANT FRONT THERMOSTAT BULB NATURAL N/A VCR351A-H VCR501A-H VCR701A-H
RADIANT FRONT THERMOSTAT BULB L.P. N/A VCR352A-H VCR502A-H VCR702A-H
HEIGHT 20” 26” 26” 30”
WIDTH 24” 30” 30” 36”
DEPTH 15-1/4” 15-1/4” 19-1/4” 19-1/4”
INPUT (BTU/HR.) 20,000 35,000 50,000 70,000
GAS INLET/OUTLET SIZE 1/2X3/8” 1/2X3/8” 1/2X3/8” 1/2X3/8”
VENT SIZE 3” 4” 4” 5”
CENTER OF VENT TO FLOOR 16-1/2” 21-1/2” 21-1/2” 25-1/2”
NUMBER OF RADIANTS (“VCR” SERIES) N/A 5 5 5
NUMBER OF RADIANT GLASS (“VCR” SERIES) N/A 2 2 2
APPROX. SHIPPING WEIGHT (“VC” SERIES) 55 LBS. 84 LBS. 112 LBS. 138 LBS.
APPROX. SHIPPING WEIGHT (“VCR” SERIES) N/A 96 LBS. 124 LBS. 150 LBS.
*OPTIONAL BLOWER MODEL N/A CHB-3 CHB-3 CHB-3
*Blowers also available factory mounted on 50M Btu units. All 70M Btu units come with blower mounted only.
SPECIFICATIONS
Page 2