Filter
Top Products
General Programming Operation:
5-1-1 programming allows you to create a heating schedule that is specific to
your needs: weekdays, Saturday, and Sunday. Weekdays are a single unit,
meaning the program schedule will be the same for Monday, Tuesday,
Wednesday, Thursday, and Friday. Saturday and Sunday can each have
individual programs. Every weekday, Saturday, or Sunday program has 4 daily
settings: WAKE, LEAVE, RETURN, and SLEEP.
✦ WAKE: The desired room temperature and time the heating period should
begin when you are present in the morning. If desired, allow 15 minutes
prior to wake time for the room to reach comfort level.
✦ LEAVE: The time and the lower desired temperature you would like your
room to be when you leave for the day. This is an energy saving period.
✦ RETURN: The desired room temperature and time the heating period
should begin when you are present in the evening. If desired, allow 15
minutes prior to your return time for the room to reach comfort level.
✦ SLEEP: The time and the lower desired temperature you would like your
room to be while you sleep. This is an energy saving period.
Each setting needs to be programmed with a time and temperature.
Programming begins by directing you to set the time of day for the 4 daily
settings for weekdays, Saturday, and Sunday. Once all times have been set, the
program will direct you to set the temperatures for the 4 daily settings for
weekdays, Saturday, and Sunday.
Operation Modes:
✦ The AUTOmatic mode runs the programmed sequence recorded by the
user. Use this mode when daily comfort needs and routine are in
accordance with the recorded program.
✦ The MANUAL mode overrides the recorded program sequence. Use this
mode when out of town or when maintaining a certain temperature set
point for an extended period of time is desired. Setting the manual
temperature to a cool set point of 62 degrees or less helps reduce ener-
gy costs. The MANUAL mode stays active until the AUTOmatic program
is activated.
✦ The Temporary Setpoint overrides the programmed temperature when
AUTO mode is activated. Set a Temporary Setpoint when changing the
temperature for a given period of the day. The setpoint will stay active until
the next programmed period for the given day.
Energy Saving Tips:
Here are a few tips to maximize energy saving capabilities:
✦ When programming, always set the temperature back for a minimum of 8
hours when away from home or asleep.
✦ Each 2-degree decrease for an 8 hour period is equivalent to a 2% savings.
✦ Maximize the 8 hour temperature set back by reducing the setpoint 8 to
10 degrees from your preferred comfort setpoint.
✦ Use the manual mode to set and hold the temperature back 8 degrees or
more while on vacation.
✦ Or, maintain default program. The thermostat comes equipped with
an energy saving program, as outlined in the “Default Settings” table.
1. To activate the PROGRAM MODE,
press the MODE button. CLOCK,
NEXT, SCHED appear on the display.
3. To set the hours, press the down
▼
button to decrease the hour or the
up
▲
button to advance. Note: the
clock is a 24 hour clock and will display
AM or PM to distinguish time of day.
The AM/PM icon will change with
setting the hours.
5. Press the MODE button to activate
the set day of week mode. The SU icon
will flash. To set the day, press the
down
▼
button to select the previous
day or the up
▲
button to select the
next day. Only the selected day will
show on the LCD. Press the MODE
button to save your selection.
2. To activate the CLOCK MODE,
press the DOWN
▼
button. The hour
numerals will flash.
4. Press the MODE button to activate
the set minutes mode. The minute
numerals will flash. To set the minutes,
press the down
▼
button to decrease the
minutes or the up
▲
button to advance.
PROGRAMMING THE
AUTO SCHEDULE
1.To activate the PROGRAM MODE,
press the MODE button once. CLOCK,
NEXT, SCHED appear on the display.
3. To program the WAKE time setting,
press the down
▼
button to decrease
the time or the up
▲
button to increase.
When the time setting is correct, press
the MODE button to advance to
program the LEAVE time setting.
5. To program the RETURN time
setting, press the down
▼
button to
decrease the time or the up
▲
button
to increase. When the time setting is
correct, press the MODE button to
program the SLEEP time setting.
7. To program the WAKE, LEAVE,
RETURN and SLEEP time settings for
both Saturday (SA) and Sunday (SU),
return to the beginning of the
PROGRAMMING AUTO SCHEDULE
instructions and repeat.
2. To activate the AUTO SCHEDULE
program mode, press the up
▲
button
once. The first display will be the WAKE
time for Monday through Friday. Time
adjustments are made in 15 minute
increments.
4. To program the LEAVE time setting,
press the down
▼
button to decrease
the time or the up
▲
button to increase.
When the time setting is correct, press
the MODE button to advance to
program the RETURN time setting.
6. To program the SLEEP time setting,
press the down
▼
button to decrease
the time or the up
▲
button to increase.
When the time setting is correct, press
the MODE button to program the
Saturday WAKE time setting.
8. After programming the Saturday and
Sunday time settings, press the MODE
button to program the Monday through
Friday WAKE setpoint temperature. To
program setpoint temps, press the
down
▼
button to decrease the temp
or the up
▲
button to increase. When
the temperature setting is correct,
press the MODE button to advance to
program the LEAVE temp.
9. Continue to program the setpoint
temperatures by pressing the MODE
button to advance to LEAVE, RETURN
and then SLEEP. For each schedule,
press either the down
▼
button or the up
▲
button to program the correct setpoint.
Press the MODE button to advance.
AUTO and MANUAL Modes:
Selecting AUTO or MANUAL
MODE:
1. To select the AUTO or MANUAL
operating mode, press the MODE button
twice. The MANUAL, RUN, AUTO
appear on the display. The current mode
is identified by a flashing underline. Press
the down
▼
button to select MANUAL
mode or the up
▲
button to select AUTO
mode. To activate the selected operating
mode, press the MODE button again.
Setting a Temporary Setpoint:
3. To set a temporary setpoint
(AUTO mode only), press either the
down
▼
button or the up
▲
button to
display the current setpoint. To change
the setpoint, press the down
▼
button to
decrease the setting or press the up
▲
button to increase. TEMP is displayed to
indicate that a temporary setpoint is
active. The temporary setpoint will be
canceled when the next programmed
operating setting has been activated
(WAKE, LEAVE, RETURN or SLEEP). It
may also be canceled by adjusting the
setpoint up or down until the TEMP icon
disappears.
Before you program your thermostat, take a moment and write a program suitable
to your needs and schedule. You will need to know this before programming the
thermostat. Use the default settings guide above as a guideline.
Programming Instructions:
START UP
How To Press Buttons For Programming:
✦To change the temperature set point, press the down
▼
or up
▲
button and hold,
release when desired set point is reached. Temperature increases or decreases
in 1 degree increments.
✦To change the time of day, press the down
▼
or up
▲
button and hold, release
when desired set point is reached. Time of day increases or decreases in 15 minute
increments.
✦For all other functions, press once to make changes or selections.
Setting the Time of Day and Day of Week:
10. Continue to program the setpoint
temperatures for Saturday and Sunday
by pressing the MODE button to
advance. For each schedule, press
either the down
▼
button or the up
▲
button to program the correct setpoint.
When you have completed the
programming, press the MODE button
to save.
Adjusting MANUAL Setpoint:
2. To adjust the MANUALmode setpoint,
press either the down
▼
button or the up
▲
button to display the current manual
setpoint. To change the setpoint, press
the down
▼
button to decrease the
setting or press the up
▲
button to
increase. The thermostat will
automatically return to the time/room
temperature display within 30 seconds.
* The SMART-BASE thermostat has been simulated to offer the best performance
for a built-in control. The concept is to simulate a midpoint temperature of the room,
respond to this setting, and maintain it for optimum comfort. However, keep in mind
that temperature variances to this reading could be affected by drafts within the wall
area, cold air from flooring or drafts from a nearby window or door.
©2005 Cadet Manufacturing Co. Printed in U.S.A. 12/05 #720002
The default schedule only applies at the
first start of the microprocessor. When
the thermostat has been programmed,
the default values no longer apply.
Programmed values are retained if the
heater power is interrupted or turned OFF.
Once the power is restored, the thermostat
will be in AUTO mode. However, the clock and
day of the week will require reprogramming.
The thermostat will load its default
program settings when power is
established for the first time. The display
will alternate between a room temperature
display and a time of day display. Both the
time of day and room temperature
displays will continuously flash to indicate
that a power interruption has occured.
* Room
Temperature
Time of Day