Filter
Top Products
Installation Instructions
1. Remove the heater front panel by lifting up and pulling out on the bottom edge of the front panel.
Set the front panel aside.
2. Remove the junction box cover at the left end of the heater by removing the screw (See Figure 1).
Keep screw for future use.
3. If you are installing the EBKA-1-24 thermostat kit as part of a new installation, proceed to Step 6.
4. Disconnect the power supply wires and remove the wiring strain relief device from the heater.
5. Remove heater from the wall by lifting the heater off the mounting brackets. It is best to replace the
thermostat while the heater is not mounted.
6
. Remove the existing left end cap or EBKA-1-24 thermostat kit by removing the screw and clip located
on the back of the heater and sliding the end cap away from the heater. Keep screw and clip for future use.
7. Attach the new EBKA-1-24 thermostat kit with the indicator light on top by sliding it onto the heater,
making sure no wires are caught between the thermostat and heater. Secure in place using the screw
and clip previously removed in Step 6.
8. Route power supply wires through the
wiring knockout hole and secure to heater
using the strain relief connector. If this is a
new unit, refer to the EBHA owner’s guide
for instructions on how to install the heater.
9. Attach heater to the wall mounting
brackets, making sure the power supply
wires are not pinched between the wall
and the heater.
10. Connect one red wire from the thermostat
to one power supply wire. Connect
remaining red wire from thermostat to
remaining power supply wire.
11. Connect one black wire from the
thermostat and one black wire from the
indicator light to one black wire from the heater. Connect the remaining black wire from the thermostat
and black wire from the indicator light to the remaining black wire from the heater.
12. Connect ground to grounding screw provided in junction box.
Note: All wires must be used.
13. Inspect all wire connections to be sure they are fastened securely. Push wiring back into the junction
box and re-attach the junction box cover using screw previously removed.
14. Reattach the heater front panel and turn the thermostat to the lowest position.
15. Restore power at the electrical panel board (circuit breaker or fuse box).
16. Rotate the thermostat control knob to a higher setting until the indicator light turns on.
IMPORTANT: All wiring must comply with all local electrical codes.
READ ALL
INSTRUCTIONS
A
ND SAFETY
INFORMATION.
WARNING!
Risk of electrical
shock. Turn off all
power at the
electrical panel
board supplying
power to the
heater before
doing any
electrical wiring.
WARNING!
Do not hit or damage
the temperature limit
sensing switch on
this heater.
WARNING!
Do not operate the
heater without the
front cover in place.
IMPORTANT!
It is extremely
important that you
verify the electrical
supply wires are the
same voltage as the
heater (i.e. 120 volt
heater to 120 volt
power supply and
240 volt heater to 240
volt power supply).
©2007 Cadet Manufacturing Co. Printed in U.S.A. Rev. 11/07 #706982
Warranty
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any
Cadet product, including thermostats, found to be defective within
one year after the date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance,
misuse, abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet.
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT
AS SET OUT HEREIN. CADET SHALL NOT BELIABLE FOR DAMAGES
SUCH AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL
DAMAGES AND/OR INCIDENTAL EXPENSES RESULTING FROM
BREACH OF THESE WRITTEN WARRANTIES OR ANY EXPRESS OR
IMPLIED WARRANTY.
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR
CADET PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE
SAME WARRANTIES AS THE PRODUCT. THE INSTALLATION OF
REPLACEMENTPARTSDOESNOTMODIFYOREXTENDTHEUNDERLYING
WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT
OR PART DOES NOT CREATE ANY NEW WARRANTIES.
8. These warranties give you specific legal rights, and you may also
have other rights which vary from state to state. Cadet neither
assumes, nor authorizesanyone to assume for it,any other obligation
or liabilityin connectionwith its products otherthan asset outherein.
If you believe your Cadet product is defective, please, contact Cadet
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Parts and Service
Visit www.cadetco.com/parts_service for information on where to
obtain Parts and Service.
How to operate your thermostat
1. Once installation is complete and power has been restored, turn the thermostat knob to the highest position.
2. When the room reaches your comfort level, slowly turn the thermostat knob down to a lower setting until the
light goes off or a click sound is heard. The heater will automatically cycle around this preset temperature.
3. To reduce the room temperature, turn the knob to a lower setting. To increase the room temperature,
turn the knob to a higher position.
Operation
2
PILOT
L
IGHT
E
LEMENT
T
ERMINALS
LIMIT CONTROL
E
BKA-1-24
THERMOSTAT
SUPPLY WIRES
B
LACK
BLACK
RED
RED
C
RIMP
CONNECTOR
C
RIMP
CONNECTOR