Filter
Top Products
Installation Instructions
CGH562 – 30 AMP
Receptacle
Configuration
Grounding Instructions
This heater is for use on 240 (or 208) volts. The cord has a plug as
shown to the right. No adapter is available for this blade configu-
ration, and none should be used. The outlet type is a 240 (or 208)
volt grounding outlet. When properly installed, it provides a
ground connection through the cord to the heater to protect the
operator from electrical shock.
MODEL WATTS VOLTS (60 Hz) BTUs AMPS PLUG TYPE
CGH562 5600 / 4200 240 / 208 19,107 / 14,322 23.4 / 20.2 30 Amp
Specifications
Operation and Maintenance
How To Operate Your Heater
1. Turn the thermostat knob fully clockwise .
2. When the room reaches your comfort level, turn the thermostat
knob counter clockwise until the heater shuts off. One or
two minor adjustments may be necessary as the heat becomes
better distributed throughout the area.
3. To reduce the room temperature, turn the knob counter clockwise .
To increase the room temperature, turn the knob clockwise .
Continuous Fan Operation
In order to activate the continuous fan feature, set rocker switch
to the “ON” position. The elements will continue to cycle according
to the thermostat setting. For no heat, turn the thermostat knob to
full counterclockwise position . With fan in “AUTO” position, fan
will cycle with the thermostat.
Maintenance, Cleaning, & Storage
The motor is permanently lubricated. This heater does not require
routine maintenance other than the occasional cleaning of the
intake grill opening to prevent clogging.
WARNING WHEN CLEANING HEATER, BE SURE TO
DISCONNECT HEATER CIRCUIT.
To disconnect heater, turn thermostat control knob to full
counterclockwise position, then remove plug from electrical
outlet before cleaning or performing any maintenance. Allow
heater to cool. IMPORTANT: Heater must be unplugged before
performing any maintenance.
To clean air intake grill use vacuum with brush attachment or high
pressure air. If the heater malfunctions or has been damaged, or
if the cord or plug has been damaged, repairs must be made by a
qualified electrician or authorized service facility. Do not operate
until repairs have been made.
For dusting, use a soft cloth. For cleaning, use only a damp rag and
nonabrasive dish detergent. Do not use abrasive or chemical
cleaners as these may damage the finish. If heater is used in a
dusty location, use a vacuum cleaner dust brush to remove dust
and other foreign particles from the grill. Always unplug cord and
wind it around heater handles when not using. Keep heater in a
safe location for storage.
Any other servicing should be performed by an authorized
service representative.
When the heater is not in use, unplug and store in a clean, dry
environment. The handle may also be used to wrap the power
cord around for safe storage.
Temperature Limiting Device
All heaters are equipped with thermally actuated auto reset limit
protection which automatically disconnects heating element
and motor in the event normal operating temperatures are
exceeded. If heater should fail to operate with thermostat turned
clockwise to its limit, disconnect heater and wait a few minutes
allowing heater to cool. Operation of the safety thermal limit
control invariably indicates that the heater has been subjected to
abnormal conditions, such as a partial or complete blockage of the
air intake or exit. Be sure to keep these areas clear in order to allow
proper air circulation. It is recommended that the heater be
checked by a qualified electrician or repair service to insure the
heater has not sustained any damage.
Warranty
WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET
PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME
WARRANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT
PARTS DOES NOT MODIFY OR EXTEND THE UNDERLYING
WARRANTIES. REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR
PART DOES NOT CREATE ANY NEW WARRANTIES.
8. These warranties give you specific legal rights, and you may also have
other rights which vary from state to state. Cadet neither assumes, nor
authorizes anyone to assume for it, any other obligation or liability in
connection with its products other than as set out herein.
If you believe your Cadet product is defective, please, contact Cadet
Manufacturing Co. at 360-693-2505, during the warranty period, for
instructions on how to have the repair or replacement processed.
Warranty claims made after the warranty period has expired will be
denied. Products returned without authorization will be refused.
Parts and Service
Visit http://support.cadetco.com for information on where to obtain parts
and service.
Maintenance: For more effective and safer operation and to prolong the
life of the heater, read the Owner’s Guide and follow the maintenance
instructions included with each heater. Failure to properly maintain the
heater will void any warranty and may cause the heater to function
improperly. Warranties are non transferable and apply to original
consumer only. Warranty terms are set out below.
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any Cadet
Garage/Utility Unit Heater (CGH) element or motor found to be defective
within one year after the date of purchase.
THESE WARRANTIES DO NOT APPLY:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance, misuse,
abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS
SET OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH
AS PROPERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR
INCIDENTAL EXPENSES RESULTING FROM BREACH OF THESE WRITTEN
©2010 Cadet Manufacturing Co. Printed in U.S.A. Rev. 12/10 #720102
Floor Application
This heater may be used for floor or flat surface mounting. After
placing the heater on floor or other flat surface in an appropriate
location, insert plug into the proper type wall outlet.
Wall or Ceiling Mount Application
Heater can be mounted on wall or ceiling with proper anchoring
provisions. The wall/ceiling mounting structure and anchoring
provisions must be of sufficient strength to support the combined
weight of the heater and mounting bracket.
Plug
Configuration
CAUTION: Heater will operate on either 240 or 208 volts. Check heater
voltage and phase on label on back of heater to make sure they are
the same as the electrical service supplied. See plug configuration.
Altering the cord in any way will void the warranty! Be sure that
the electrical receptacle is of the configuration and capacity
appropriate for the heater.