Filter
Top Products
Cat. No.
5919/5919TH
AC Powered
Photoelectronic
Interconnectable
Smoke Alarm
DESCRIPTION:
The BRK Electronics Cat. No. 5919 is a 120V AC powered
photoelectronic unit designed for both single and multiple station use, up
to 18 units. Its sensor operated on the scattered light principle, and
electronically compensates for ambient light conditions. The unit has its on
85dB electronic alarm horn, powered-on LED and test button. It is
interconnectable and comes with a plastic bracket that mounts easily to
3" and 4" octagon, 4" square or single gang boxes. The 5919 comes
with a plug-in connector.
This detector is designed so that, when interconnected, if any one of the
units senses smoke, its LED will turn off and its alarm will sound. All other
interconnected units will sound an alarm but their LEDs will remain on.
NOTE: All interconnected units must receive power from the same fuse or
breaker.
Cat. No. 5919TH is identical to the 5919 but has a thermal sensor which
is not connected to the unit. The thermal can be separately connected to a
central control panel—ideal for hotels and hospitals. This sensor has its
own plug-in connector and has a N.O. contact (Form A) rated 3A at
125V AC, a! at 30V DC.
SPECIFICATION
The smoke alarm shall be powered by a 120V AC, 650Hz. power
source and shall be listed at .025A in standby condition. The alarm
shall have a solid state photoelectronic sensor that operated on the
scattered light principle. It shall be protected by an insect-resistant
screen. The sensor shall sample the air at the alarm every 5 seconds
and shall be designed to trigger an alarm if prescribed levels of
smoke enter its chamber. The alarm shall electronically compensate for
ambient light conditions and shall be cable of operating properly
between 40° and 100°F (4°-38°C) and relative humidity between
10% and 90%. A built-in test button shall mechanically simulate the
presence of smoke. A built-in light-emitting diode shall glow when
AC power is being received. The alarm shall have an electronic alarm
horn. It shall have a plug-in connector and be capable of interconnection
with eleven other identical units. It shall be listed to UL 217.
MANUFACTURED BY: DISTRIBUTED BY:
FOR TECHNICAL HELP OR REPRESENTATIVE NEAREST YOU
PHONE 1-800-392-1395
8AM-5PM (CENTRAL TIME)
CM2154
BRK
®
Electronics
3901 Liberty Street Road
Aurora, IL60504-8122
©1998 BRK Brands, Inc.
Made in USA
TECHNICAL SPECIFICATIONS
Alarm Circuit 100% solid state
Alarm Dimensions 5.5" diameter, 2.5" height
Operating 40°F(4.4°C) to 100°F(38°C)
Temperature Range
Operating Humidity 50%RH to 90%RH
Range
Audio Alarm 85dB at 10ft.
Power Indicator Lamp Solid State LED
Test Button Mechanically simulated the presence of smoke in
photoelectronic sensing chamber, causing unit to alarm
Alarm Reset Automatic when smoke clears
Interconnections Up to 18 units
Weight 8 ounces
Power Consumption .025 Amps typical in standby
.025 Amps in alarm
Thermal 135°F, 50 foot space rating (cannot be used where
ambient temperature exceeds 95°F). CONTACTS - Form
A, Ratings: 3A @ 125V AC @ 30V DC
MAXIMUM INTERCONNECT BUS LENGTH 1000 FEET FOR #12-#14 GAUGE WIRE.
ALL INTERCONNECTED SMOKE ALARMS MUST BE POWERED FROM THE SAME FUSE OR BREAKER.
INSTALL PER LOCAL ELECTRICAL CODES AND ARTICLE 780 OF THE NATIONAL ELECTRICAL CODE.
{
A
1
3
}
B
1
2
3
4
5
6
8
7
{
{
4
5
6
8
7
{
{
4
5
6
8
7
{
{
MAXIMUM INTERCONNECT BUS LENGTH 1000 FEET FOR #12-#14 GAUGE WIRE.
ALL INTERCONNECTED SMOKE ALARMS MUST BE POWERED FROM THE SAME FUSE OR BREAKER.
INSTALL PER LOCAL ELECTRICAL CODES AND ARTICLE 780 OF THE NATIONAL ELECTRICAL CODE.
Model 5919
Model 5919TH
Model 5919 Model 5919TH