Filter
Top Products
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
PAGE NO
7
Installing LP Gas Tank
4O OPERATE YOU WILL NEED PRECISIONFILLED STANDARD GRILL ,0 GAS
TANK LBS WITH EXTERNAL VALVE THREADS
Note: !N EMPTY STANDARD GRILL ,0 GAS TANK WEIGHS APPROXIMATELY
LBS ! PRECISIONFILLED STANDARD GRILL ,0 GAS TANK SHOULD WEIGH
NO MORE THAN LBS
#AUTION ,0 GAS TANK MUST BE PROPERLY
DISCONNECTED AND REMOVED PRIOR TO MOVING THIS
HEATER
)NSERT ,0 'AS 4ANK
0LACE PRECISION FILLED ,0 GAS TANK UPRIGHT INTO HOLE IN PATIO HEATER SO IT IS ARRANGED FOR VAPOR
WITHDRAWAL
3ECURE ,0 'AS 4ANK
3ECURE TANK IN PLACE BY ATTACHING LOOSE END OF TANK RESTRAINT CHAIN TO HOLE IN RIGHT LEG
#ONNECT ,0 'AS 4ANK
Before connecting, be sure that there is no debris caught in
THE HEAD OF THE ,0 GAS TANK HEAD OF THE REGULATOR VALVE OR
IN THE HEAD OF THE BURNER AND BURNER PORTS
#ONNECT GAS LINE TO TANK BY TURNING KNOB CLOCKWISE UNTIL IT
STOPS
$ISCONNECT ,0 'AS 4ANK
"EFORE DISCONNECTING MAKE SURE THE ,0 GAS TANK VALVE IS
h#,/3%$v
Disconnect gas line from LP gas tank by turning knob
COUNTERCLOCKWISE UNTIL IT IS LOOSE
#AUTION ,0 GAS TANK MUST BE PROPERLY
DISCONNECTED AND REMOVED PRIOR TO MOVING
THIS HEATER
.EED A TANK OF GAS 4RY TANK EXCHANGE SERVICE )TS EASY
FAST SAFE AND AVAILABLE AT TENS OF THOUSANDS OF CONVENIENTLY
LOCATED RETAIL OUTLETS NATIONWIDE 9OU CAN PURCHASE A NEW FULL
TANK OR EXCHANGE YOUR EMPTY FOR A PRECISION FILLED ONE
20 lb
9 Kg
17.9 in. / 45.5 cm
12.2 in. / 31 cm
#HECKING FOR ,EAKS
"URNER #ONNECTIONS
-AKE SURE THE REGULATOR VALVE AND HOSE CONNECTIONS ARE SECURELY FASTENED TO THE BURNER AND
THE TANK
)F YOUR UNIT WAS ASSEMBLED FOR YOU VISUALLY CHECK THE CONNECTION BETWEEN THE BURNER PIPE
AND ORIFICE -AKE SURE THE BURNER PIPE FITS OVER THE ORIFICE
7!2.).' &AILURE TO INSPECT THIS CONNECTION OR FOLLOW THESE
INSTRUCTIONS COULD CAUSE A FIRE OR AN EXPLOSION WHICH CAN CAUSE DEATH
SERIOUS BODILY INJURY OR DAMAGE TO PROPERTY
)F THE BURNER PIPE DOES NOT REST FLUSH TO THE ORIFICE
PLEASE CONTACT FOR ASSISTANCE
4ANK'AS ,INE #ONNECTION
-AKE OZ OF LEAK SOLUTION BY MIXING ONE PART LIQUID
DISHWASHING SOAP WITH THREE PARTS WATER
-AKE SURE CONTROL KNOB IS IN h/&&v POSITION &IGURE
4URN ,0 GAS TANK VALVE TO h/0%.v
3POON LEAK CHECK SOLUTION AT ALL h8v LOCATIONS
(Figures 1 and 2)
A )F ANY BUBBLES APPEAR TURN ,0 GAS TANK VALVE TO
h#,/3%$v RECONNECT AND RETEST
B )F YOU CONTINUE TO SEE BUBBLES AFTER SEVERAL
ATTEMPTS TURN ,0 GAS TANK VALVE TO h#,/3%$v
disconnect LP gas tank and contact
FOR ASSISTANCE
B )F NO BUBBLES APPEAR AFTER ONE MINUTE TURN ,0 GAS
TANK VALVE TO h#,/3%$v WIPE AWAY SOLUTION AND
PROCEED
"EFORE ,IGHTING
(EATER SHOULD BE THOROUGHLY INSPECTED BEFORE EACH USE
AND BY A QUALIFIED SERVICE PERSON AT LEAST ANNUALLY
)F RELIGHTING A HOT HEATER ALWAYS WAIT AT LEAST
MINUTES
)NSPECT THE HOSE ASSEMBLY FOR EVIDENCE OF EXCESSIVE
ABRASION CUTS OR WEAR 3USPECTED AREAS SHOULD BE
LEAK TESTED )F THE HOSE LEAKS IT MUST BE REPLACED PRIOR
TO OPERATION /NLY USE THE REPLACEMENT HOSE ASSEMBLY
SPECIFIED BY MANUFACTURER
,IGHTING
Note: 4HIS HEATER IS EQUIPPED WITH A PILOT LIGHT THAT ALLOWS
FOR SAFER STARTUPS AND SHUTDOWNS 0ILOT MUST BE LIT BEFORE
MAIN BURNER CAN BE STARTED
#ONTROL KNOB MUST BE IN THE h/&&v POSITION &IGURE
4URN ,0 GAS TANK VALVE TO h/0%.v
/PEN VIEWING HOLE BY SLIDING COVER TO EITHER SIDE
&IGURE
0USH CONTROL KNOB IN AND ROTATE TO h0),/4v POSITION
&IGURE
Note: For initial start or after any tank change, hold control
knob in for 2 minutes to purge air from gas lines before
PROCEEDING
Push-button Ignition: Immediately push igniter button
A COUPLE OF TIMES 0ILOT LIGHT FLAME WILL APPEAR AND BE
VISIBLE THROUGH VIEWING HOLE
Electronic Ignition: Immediately push igniter button for
FIVE SECONDS 0ILOT LIGHT FLAME WILL APPEAR AND BE
VISIBLE THROUGH VIEWING HOLE
2ELEASE CONTROL KNOB AFTER SECONDS 0ILOT LIGHT WILL
REMAIN LIT
)F IGNITION DOES NOT OCCUR TURN CONTROL KNOB h/&&v WAIT
MINUTES AND REPEAT LIGHTING PROCEDURE
4URN CONTROL KNOB TO h()'(v &IGURE -AIN BURNER WILL
LIGHT IMMEDIATELY &LAME IS VISIBLE THROUGH VIEWING HOLE
)F NOT TURN CONTROL KNOB h/&&v WAIT MINUTES AND
REPEAT LIGHTING PROCEDURE
)F FOR SOME REASON YOUR IGNITOR FAILS TO DELIVER A SPARK
your heater can be started by inserting a lit match
THROUGH THE PILOT VIEW HOLE WHILE PUSHING THE CONTROL
KNOB IN WHILE IN THE h0),/4v POSITION
7!2.).' "E CAREFUL WHEN ATTEMPTING TO
MANUALLY IGNITE THIS HEATER (OLDING IN THE
CONTROL KNOB FOR MORE THAN SECONDS
BEFORE IGNITING THE GAS WILL CAUSE A BALL OF
FLAME UPON IGNITION
(AVE A QUESTION OR ARE HAVING PROBLEMS VISIT
WWWBLUERHINOCOM OR CALL
Figure 1
X
Figure 2
Figure 3
PILOT / VEILLEUSE
PUSHINPRESSEZ ETMAINTENEZ
LOW /
BAS
HIGH /
HAUT
OFF /
ARRÊT
&IGURE
PILOT / VEILLEUSE
PUSHINPRESSEZ ETMAINTENEZ
LOW /
BAS
HIGH /
HAUT
OFF /
ARRÊT
Figure 5
PILOT / VEILLEUSE
PUSHINPRESSEZ ETMAINTENEZ
LOW /
BAS
HIGH /
HAUT
OFF /
ARRÊT
&IGURE
6IEW (OLE
Operating Instructions