Filter
Top Products
6
ENGLISH
(Original instructions)
u Hang the appliance on the wall by placing the opening
on the base of the vac over the hooks in the wall mount
bracket.
Assembly
Accessories (g .B)
These models may be supplied with some of the following
accessories:
u A squeege tool (12) for wet use on hard surfaces.
(WD4810N, WD7210N, WD9610ECN and WD9610N
Only)
u A powered brush head (13) for vacuuming on cut pile
carpeting. The brush head is particularly useful for picking
up hair, threads, etc. (DV9610PN Only)
Fitting (Fig. D)
u Insert the appropriate accessory into the front of the appli-
ance. Make sure that the accessory is pushed fully in.
Use
u Before rst use, the battery must be charged for at least
24 hours.
u Place the appliance on the charging base whenever it is
not in use. (WD4810N, WD7210N and WD9610N Only)
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. E & F)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch in the on posi-
tion.
u Plug the jack plug of the charger (6) into the charg-
ing socket (4) of the appliance (Fig. E). (DV4800N,
WD9610ECN and DV9610PN Only)
u Place the appliance on the charging base (7) (Fig. F).
(WD4810N, WD7210N and WD9610N Only)
u Plug in the charger. Switch on at the mains. The charging
indicator (3) will be lit.
u Leave the appliance to charge for at least 16 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indenitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Switching on and off (g. G)
u To switch the appliance on, slide the on/off switch (1)
forward to position 1.
u To switch the appliance off, slide the on/off switch (1) back
to position 0.
Dry pick up (DV4800N, DV9610PN)
u For everyday spills of dry material.
Wet and dry pick up (WD4810N, WD7210N,
WD9610ECN and WD9610N Only)
u For everyday spills of dry material, use your appliance
without the squeegee accessory.
Warning! Your product is designed for light spills only.
u This appliance can also be used to pick up everyday liquid
spills. Use the squeegee accessory on non-absorbent,
hard surfaces. On absorbent surfaces, such as carpet,
your appliance will pick up wet spills better without the
accessory.
u For best performance on hard surface wet pickups, insert
squeegee into the bowl nozzle opening.
u For best results when using this accessory, hold the appli-
ance at an angle of 45° and pull it slowly towards you.
u Do not ll the bowl beyond the end of the intake chute. If
there is any liquid in the bowl, do not turn the unit upside
down, sideways, point the nozzle upward, or shake the
vac excessively.
u After picking up liquid substances clean the appliance and
lter immediately. Mold and mildew may form if the unit is
not properly cleaned after wet pickups.
u Before charging, be sure to empty all liquid contents and
dry thoroughly, to avoid damage to your appliance.
Optimising the suction force
In order to keep the suction force optimised, the lters must be
cleared regularly during use.
Emptying and cleaning the product.
Removing the dust bowl and lters (g. H, I, J & K).
Warning! The lters are re-usable and should be cleaned
regularly.
u Press the release latch (2) and pull the dust bowl (5)
straight off.
u While holding the dust bowl over a bin or sink, pull out the
lter to empty the contents of the bowl.
u To replace the dust bowl, place it back onto the handle
until it “clicks” rmly into position.
Warning! Never use the appliance without the lters. Opti-
mum dust collection will only be achieved with clean lters.
Foam insert (g. J) (WD4810N, WD7210N,
WD9610ECN and WD9610N)
u Place the foam insert (10) into the centre of the wet/dry
deector (11).
Warning! Never use the appliance for wet applications without
the water deector and foam insert tted.