Filter
Top Products
5
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER steam mop has been designed for
sanitising and cleaning sealed hardwood, sealed laminate,
linoleum, vinyl, ceramic tile, stone and marble oors and for
refreshing carpets. This appliance is intended for indoor
household use only.
Warning! Read all of the 'Safety, Maintenance,
Service' manual carefully before operating
this appliance.
Read all of this manual carefully before operating
the appliance.
Features
This appliance includes some or all of the following features.
1. ON/Off switch
2. Lock off button
3. Trigger switch
4. Steam nozzle
5. Hand held steam cleaner
6. Autoselect
TM
button
7. Filler cap
8. Water tank
9. Steam mop body
10. Handle
11. Steam head
12. Steam head cleaning pad
14. Carpet glider
15. Bottom cable tidy hook
16. Top cable tidy hook
17. Cable management clip
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
u Slide the bottom end of the handle (10) into the top end of
the steam mop body (9) until it clicks into place. The arrow
on the handle (10) should be aligned with the top of the
steam mop body (9).
Attaching the steam head (Fig. B)
u Slide the bottom end of the steam mop body (9) onto the
steam head (11) until it clicks into place.
u The steam head can be removed from the Steam mop
body by pressing the steam head release button (19) and
pulling the steam mop body (9) off the steam head (11).
Attaching the hand held steam cleaner (Fig. C)
u Holding the back of the steam mop body (9) Push the
hand held steam cleaner (5) rmly into the steam mop
body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to
conrm the unit is docked.
Warning! Inspect that the seal (26 Fig. J) on the steam nozzle
(4) before tting the hand held steam mop to the steam mop
body. If the seal is missing or damaged then please contact
your nearest authorised repair agent. Do not use the appli-
ance.
Removing the hand held steam cleaner (Fig. C)
u Push the release button (20) down and pull the hand held
steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your
BLACK+DECKER dealer:
Steam head cleaning pad (12) - cat. no. FSMP20-XJ).
u Place a cleaning pad (12) on the oor with the ‘hook &
loop’ side facing up.
u Lightly press the steam mop down onto the cleaning pad
(12).
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Wait until the steam mop cools down. (approximately ve
minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (21) and press down rmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Filling the water tank (Fig. F)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
u Open the ller cap (7) by ipping it down.
u Fill the water tank (8) with water.
Warning! Your water tank has a 0.36 litre capacity.
u Re-t the ller cap (7).