Filter
Top Products
6
ENGLISH
(Original instructions)
Features
This tool includes some or all of the following features.
1. On/off switch
2. Bowl release button
3. Charging indicator
4. Charging socket
5. Dust bowl
6. Dust collector
Assembly
Accessories (g. A, B & C)
These models may be supplied with some of the following
accessories:
u A brush tool (7) for furniture and stairs.
u An Integrated brush tool (8) for furniture and stairs.
u An Integrated crevice tool (9) for conned spaces.
Fitting the brush tool (Fig. A). (DV7210ECN Only)
u Insert the accessory into the front of the appliance. Make
sure that the accessory is pushed fully in.
The integrated brush tool (Fig. B). (DV9610ECN and
DV1210ECN Only)
u Flip down the brush tool (8) at the end of the dust collec-
tor.
The integrated crevice tool (Fig. C). (DV9610ECN and
DV1210ECN Only)
u Extend the crevice tool (9) by pulling the crevice tool (9)
until it locks into position.
u Retract the crevice tool (9) by pressing the area (10) and
pushing the crevice tool (9) back into the dust collector (6).
Use
u Before rst use, the battery must be charged for at least
24 hours.
Charging the battery (Fig. D)
u Make sure that the appliance is switched off. The battery
will not be charged with the on/off switch in the on posi-
tion.
u Plug the jack plug of the charger (11) into the charging
socket (4) of the appliance (Fig. D).
u Plug in the charger. Switch on at the mains. The charging
indicator (3) will be lit.
u Leave the appliance to charge for at least 16 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indenitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
Switching on and off (g. E)
u To switch the appliance on, slide the on/off switch (1)
forward to position 1.
u To switch the appliance off, slide the on/off switch (1) back
to position 0.
Rotating the dust collector (g. F) (DV9610ECN &
DV1210ECN only
The nozzle can be rotated for better access in tight spots.
u Press the rotation release catch (12).
u Rotate the nozzle to the left or right until it clicks into
place.
Optimising the suction force
In order to keep the suction force optimised, the lters must be
cleared regularly during use.
Emptying and cleaning the product.
Emptying the dust bowl (g. G).
u Press the release latchs (13) and pull the dust collector (6)
straight off.
u Empty the contents of the bowl.
u To replace the dust collector, place it back onto the handle
until it “clicks” rmly into position.
Removing the dust bowl and lters (g. H, I, J & K).
Warning! The lters are re-usable and should be cleaned
regularly.
u Press the release latch (2) and pull the dust bowl (5)
straight off.
u While holding the dust bowl over a bin or sink, pull out the
lter (14) to empty the contents of the bowl.
u To replace the dust bowl, place it back onto the handle
until it “clicks” rmly into position.
Warning! Never use the appliance without the lters. Opti-
mum dust collection will only be achieved with clean lters.
Pre-lter (g. J) (DV7210ECN)
The Filter and pre-lter can be separated to allow better
cleaning.
u Twist the pre-lter (15) in a clockwise direction and lift
from the lter (14).