Filter
Top Products
Part No. 811237 Form No. F050304A
Page 12 of 12
Solution
Problem Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
22.1
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
Will not vacuum or has poor
vacuum performance.
Adjust nozzle position. Unclog hose or exhaust (see page 6).
Allow air to feed with debris.
Nozzle height too high or too low. Clogged hose or exhaust.
Excessive quantity of debris.
Engine will not start.
Throttle & / or stop switch in off position. Out of gasoline. Bad or
old gasoline. Spark Plug wire disconnected. Dirty air cleaner.
Hose not installed, allowing interlock wire to ground.
Abnormal vibration. Check impeller and replace if required. Check Engine.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Install hose onto housing.
20
Loose or out of balance impeller or loose engine.
Engine is locked, will not
pull over.
Debris locked inside impeller. Engine problem.
See page 6, Clearing a clogged impeller housing. Contact an engine
servicing dealer for engine problems.
19
Parts List
continued from
page 11.
* Denotes standard
hardware item that may
be purchased locally.
Purchased
from
Purchase
Date
21
Serial Plate
Record your machine model, serial number and
date-of-purchase and where purchased
R
min
-1
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
22
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET / LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
64 WASHER LOCK 3/8 *8177012 2 *8177012 2 - - - -
WASHER LOCK 5/16 EXT. TOOTH - - - - - - - - *8181008 2
65 SCREW CAP 3/8 - 16 X 1 *8041050 2 - - - - - - - - - -
SCREW CAP 3/8 - 16 X 1 1/2 ZP - - - - - 8041052 2 8041052 2
66 SCREW CAP 3/8 - 16 x 1" *8041050 12 *8041050 12 *8041050 12
67 SCREW CAP 1/4-20 X 1 1/2 *8041008 1 *8041008 1 *8041008 1
68 SCREW CAP 3/8 - 16 X 1 3/4 ZP *8041053 4 *8041053 4 *8041053 4
69 ANGLE BRKT R.H. 810917 1 811096 1 811096 1
70 SCREW CAP 5/16-18 x 1" *8041028 2 *8041028 2 *8041028 2
71 ANGLE BRKT L.H. 810916 1 810969 1 810969 1
72 SPACER 811097 1 811098 1 811098 1
73 WASHER FLAT CUT 1/4 *8171002 1 *8171002 1 *8171002 1
74 CONTROL THROTTLE ASSY 810904-1 1 811222 1 811222 1
75 SCREW MACHINE 10-24 x 1-1/2" - - - - - 8059141 2 8059141 2
76 NUT LOCK 5/16-18 THIN HT. 8161041 2 8161041 2 8161041 2
77 NOZZLE FORMED STEEL 8" 811007 1 811007 1 811007 1
78 HANDLE NOZZLE W / GRIP 811020 1 811020 1 811020 1
79 WASHER FENDER 5/16 *8172020 4 *8172020 4 *8172020 4
80 SCREW CAP 5 /16 - 18 X 1 1/2 *8041030 3 *8041030 3 *8041030 3
81 LABEL DO NOT FILL WHEN ENGINE IS HOT 400268 1 400268 1 400268 1
82 HANDLE LOOP NOZZLE 811019 1 811019 1 811019 1
83 GRIP HANDLE 500267 4 500267 4 500267 4
84 PLUG CAP 890132 4 890132 4 890132 4
85 FRAME SIDE RIGHT WA TR/HTR 811100 1 811100 1 811100 1
86 FRAME SIDE LEFT WA TR/HTR 811101 1 811101 1 811101 1
87 STRAIN RELIEF 500282 1 500282 1 500282 1
88 PLUNGER SWITCH 890440 1 890440 1 890440 1
89 TUBE HANDLE LIFT 811139 2 811139 2 811139 2
90 KNOB 3/8" SOLID HUB 811230 2 811230 2 811230 2
91 BOLT CARRIAGE 3/4 - 10 X 6" LONG *8024216 1 *8024216 1 *8024216 1
QTY
HTR1803VEU
PART NO.
TR1304HEU
PART NO.
TR1104EU
PART NO.
QTY QTYITEM DESCRIPTION
120 dB
(HTR1803VEU
MODEL)
Should a Billy Goat Machine fail due to a defect in material and/or
workmanship, the owner should make a warranty claim as follows:
-The Machine must be taken to the dealer from whom it was purchased
or to an authorized Servicing Billy Goat
Dealer.
-The owner must present the remaining half of the Warranty Registra-
tion Card, or, if this is not available, the invoice or receipt.
-The Warranty Claim will be completed by the authorized Billy Goat
Dealer and submitted to their respective Billy Goat Distributor for their
territory. Attention: Service Manager. Any parts replaced under warranty
must be tagged and retained for 90 days.
-The distributor service manager will sign off on the claim and submit it
to Billy Goat for consideration.
-The Technical Service Department at Billy Goat will study the claim and
may request parts to be returned for examination. Billy Goat will notify
their conclusions to the distributor service manager from whom the
claim was received.
-The decision by the Quality / Service department at Billy Goat to
approve or reject a Warranty claim is final and binding.
Note: To process a Warranty Claim, it is necessary to quote the Model & Serial
Number which are printed on the Billy Goat Serial Plate (See owner’s manual).