Filter
Top Products
Part No. 811126 Form No. F021602B
Page 12 of 12
Solution
Problem
Possible Cause
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
22.1
Engine Service and Warranty
Contact your nearest engine manufacturer's authorized
servicing dealer.
Will not vacuum or has poor
vacuum performance.
Adjust nozzle position. Unclog hose or exhaust (see page 6).
Allow air to feed with debris.
Nozzle height too high or too low. Clogged hose or exhaust.
Excessive quantity of debris.
Engine will not start.
Throttle & / or stop switch in off position. Out of gasoline. Bad or
old gasoline. Spark Plug wire disconnected. Dirty air cleaner.
Hose not installed, allowing interlock wire to ground.
Abnormal vibration.
Check impeller and replace if required. Check Engine.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Install hose onto housing.
20
Loose or out of balance impeller or loose engine.
Engine is locked, will not
pull over.
Debris locked inside impeller. Engine problem.
See page 6, Clearing a clogged impeller housing. Contact an engine
servicing dealer for engine problems.
19
Parts List
continued from
page 11.
* Denotes standard
hardware item that may
be purchased locally.
Purchased
from
Purchase
Date
21
Serial Plate
Record your machine model, serial number and
date-of-purchase and where purchased
R
min
-1
1803 S. Jefferson
P.O. Box 308
Lee's Summit,
MO 64063 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
Unit(Weight) Engine Power
lbs. kg kW rpm
22
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET / LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
WARRANTY PROCEDURE
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and binding.
Note:
To process a Warranty Claim, it is necessary to quote the Model
& Serial number which11 are printed on the Billy Goat Serial Plate.
64 WASHER LOCK 3/8 *8177012 2 *8177012 2 - - - -
WASHER LOCK 5/16 EXT. TOOTH - - - - - - - - *8181008 2
65 SCREW CAP 3/8 - 16 X 3/4 *8041048 2 - - - - - - - - - -
SCREW CAP 3/8 - 16 X 1 1/2 ZP - - - - - 8041052 2 - - - - -
SCREW CAP 5/16 - 24 X 3/4 G5 - - - - - - - - - - *8042026 2
66 SCREW CAP 3/8 - 16 x 1" *8041050 6 *8041050 6 *8041050 6
67 SCREW MACHINE #6-32 x 3/4 *8059094 2 *8059094 2 *8059094 2
68 NUT LOCK #6 - 32 *8164003 2 *8164003 2 *8064003 2
69 ANGLE BRKT R.H. 810917 1 811096 1 811096 1
70 SCREW CAP 5/16-18 x 1" *8041028 10 *8041028 9 *8041028 9
71 ANGLE BRKT L.H. 810916 1 810969 1 810969 1
72 SPACER 811097 1 811098 1 811098 1
73 WASHER FLAT CUT 1/4 *8171002 1 *8171002 1 *8171002 1
74 CONTROL THROTTLE ASSY 810904 1 810972 1 - - - - -
75 SCREW MACHINE 10-24 x 1/2" - - - - - *8123086 2 - - - - -
76 NUT LOCK 5/16-18 THIN HT. - - - - - 8161041 1 8161041 1
77 NOZZLE FORMED STEEL 10" 811005 1 - - - - - - - - - -
NOZZ LE FORMED STEEL 8" - - 811007 1 811007 1
78 HANDLE NOZZLE W / GRIP 811020 1 811020 1 811020 1
79 WASHER FENDER 5/16 *8172020 4 *8172020 4 *8172020 4
80 SCREW CAP 5 /16 - 18 X 1 1/2 *8041030 3 *8041030 3 *8041030 3
81 LABEL DO NOT FILL WHEN ENGINE IS HOT 400268 1 400268 1 400268 1
82 HANDLE LOOP NOZZLE 811019 1 811019 1 811019 1
83 GRIP HANDLE 500267 1 500267 1 500267 1
84 PLUG CAP 890132 2 890132 2 890132 2
85 FRAME SIDE RIGHT WA TR/HTR 811100 1 811100 1 811100 1
86 FRAME SIDE LEFT WA TR/HTR 811101 1 811101 1 811101 1
87 STRAIN RELIEF 500282 1 500282 1 500282 1
88 PLUNGER SWITCH 890440 1 890440 1 890440 1
89 TUBE HANDLE LIFT 811139 2 811139 2 811139 2
ITEM DESCRIPTION QTY
HTR1601V
PA RT NO.
TR1303H
PA RT NO.
TR1103
PA RT NO.
QTY QTY
120 dB