Filter
Top Products
SETTING TIME AND DAY
Before programming, set the clock to the correct time.
1. You can change the time format at anytime back and forth from 24
to 12 hour. To do so, maintain MIN key pressed down as HEURE
key is pressed and released. Then, release MIN key.
2. Set the day by using the JOUR key (If the current day is
" Tuesday ", press and release JOUR key until TU indicator appears
on the lower area of the screen).
3. Set the time by using the HEURE and MIN keys (For the 12 hour
format, if you are setting an afternoon or evening time, make sure
that the PM indicator is turned on at left side of the screen).
4. Close the door or press on one of the ENR keys to return to
normal operations.
OPERATING MODES
The wall switch has 2 operating modes : the MANual and AUTOmatic
modes.
In the MANual mode, it works like a regular single pole switch. By
pressing on the door, the user can turn the light on and off. The display
shows the " MAN " indicator as well as light the state (ON or OFF).
The AUTOmatic mode executes in sequence (hourly) the user's
recorded programs. To place the wall switch in this mode, press on the
door for 3 seconds until AUTO appears on the screen. The display
shows the active program number and the light state (ON or OFF).
To temporarily overpass the programming, press on the door. " AUTO
" and programmed light state indicator remain on and the overpassed
light state indicator will flash. To return in manual mode, press and hold
the door for 3 seconds until " MAN " indicator is shown on display.
MEMORY BACKUP
This programmable wall switch is equipped with a rechargeable battery
which will protect your programs during a power shut down.
Note that the screen blanks during a power failure.
CHARACTERISTICS
Model : TI052A-3W
Supply : 230 VAC, 50 / 60 Hz
LOAD : 15 Watts minimum, 500 Watts maximum
Approvals : CE
Storage temperature range : -20 to 50 °C
Operating temperature range : 0 to 50 *C
WARRANTY
AUBE TECHNOLOGIES INC. ONE YEAR LIMITED WARRANTY
This product is warranted against material defects and workmanship in
normal use for a period of one year, from the date of the original pur-
chase from authorized dealers. Warranty does not cover transportation
costs. Nor does it cover a product subjected to misuse or accidental
damage.
This limited warranty is in lieu of all other warranties, obligations or lia-
bilities expressed or implied by the company.
In no event shall AUBE Technologies inc. be liable for consequential or
incidental damages resulting from installation of this product. Within
this period, any product proven defective in normal use will be repaired
or replaced, at AUBE's option, without charge for either parts or labour,
provided that the defective product with the original sale receipt is
returned to the original dealer or is shipped pre-paid, insured and
addressed to:
AUBE TECHNOLOGIES INC.
Customer Service
20, Avenue de l'Escouvier
95205 Sarcelles Cedex
France
Tel. : 01 39 33 04 60
Fax : 01 39 33 04 79
www.aubetech.com
19/12/00 720-052002 2/2
RECORDING THE PROGRAMS
The memory of this programmable wall switch can hold up to 7
programs. Each program consists of a time ON (turn on) and a time
OFF (turn off) which can be run for a single day or for everyday of the
week.
ATTENTION : Both ON and OFF programming sequences must be
recorded.
1. Open the door of the wall switch using a small screwdriver.
2. Press on the PGM key.
The display will show the number 1 (program 1) on the lower right
corner and the program state (on/off) on the upper right corner.
Note that the clock is replaced by -- : -- -- showing that the select-
ed program is not activated.
3. Press on the JOUR key to select the day to which you want the light
to turn on.
If you want the program to be repeated each day of the week,
keep pressing on JOUR several times until every days of the week
appears on the screen all together.
4. Press on the HEURE and MIN keys to set the time to which you want
the light to turn on.
Make sure that " PM " indicator appears on the screen if you want
an afternoon period (12 hour time format).
5. Press a second time on PGM key to set the time for the light to turn
off. Repeat steps 3 and 4 to set the time.
If the program " 1 ON " is set for every day of the week, the
program " 1 OFF " will automatically be set for every day.
6. Press a third time on PGM key to record programs 2 to 7.
If you need only one program, just leave the others inactive.
If you want to erase a program, select it by using the PGM key and
then hold PGM key for 3 seconds. The program will be erased
when the display will show -- : -- --.
7. Close the door or press on one of the ENR keys to return to
normal operation.