Filter
Top Products
TH136 400-136-001-C 2008-02-01 2/2
5.4 Temporary Bypass
When the TH136 is in Auto or Frost Protection mode, you can bypass
the mode for two (2) hours. The TH136 will maintain the temperature
bypass for two (2) hours, then return to previous operating mode. Set
the temperature using these buttons . The icon corresponding to
the bypassed mode will flash to indicate the bypass.
The TH136 programmable thermostat is pre-programmed with the
following schedule:
Programs 1 and 4 are repeated from Monday to Sunday.
Programs 2 and 3 are repeated from Monday to Friday.
To modify the pre-programmed schedule, follow these steps:
n Press the button associated with the program you wish to
modify.
o Enter the program start time using the buttons.
p Press the program button again.
q Enter the desired temperature using the buttons.
r Press to exit.
NOTE: After 60 seconds of inactivity, the thermostat will automati-
cally exit programming mode.
The TH136 thermostat is equipped with the Early Start function
(deactivated by default). To activate, refer to Advanced
Programming.
You must hold the Auto button for 3 seconds to access the advanced
programming. Then, press Auto to select a menu.
n Press Auto until the desired menu is displayed.
o To modify the default programming, use the buttons and
select from the available options.
p Press to exit.
NOTE: Menus are detailed below.
8.1 Modify the Number of Programs per Day (PPd)
You can select the number of programs to be executed for each day
of the week. This means, you can run all 4 programs, only 2 (1st and
4th) or none (0).
NOTE: When none (0) is selected, the TH136 will maintain the tem-
perature setpoint of the last program.
8.2 Modify the Heating Cycles (CPH)
For greater flexibility, you can define the cycle that best suits your
requirements. The shorter the cycles, the greater your comfort.
However, your system will be activated more often when using
shorter cycles.
8.3 Modify the Frost Protection Setpoint (HLd)
Use this menu to modify the Frost Protection setpoint associated with
the Frost Protection mode. The setting range is between 5°C and
28°C. Default: 10°C.
8.4 Early Start (ES)
When Early Start is activated, the TH136 calculates the optimum start
time to obtain the desired temperature by the programmed set time.
8.5 Pump Protection (PP)
For hot water installations, it is recommended that the pump be
activated at least 15 seconds every 24 hours to avoid any seizing.
Power supply: 2 AAA (LR03) alkaline batteries
Max. resistive load: 5A @ 240 VAC
Max. inductive load: 2A @ 240 VAC
Remote input: 12 VDC / ± 10% / 5 mA
Control device: Electronic
Automatic action: Type 1B
Storage temperature: -20°C to 50°C
Operating temperature
: 0°C to 50°C, 95% relative humidity without
condensation
Temperature setpoint range: 5°C to 28°C
Temperature setpoint interval:0.5°C
Temperature display resolution:0.1°C
Temperature display accuracy:± 0.3°C
Software: Class A
Protection degree:IP 20
Environment: normally polluted
Aube warrants this product, excluding battery (if applicable), to be free from defects in the
workmanship or materials, under normal use and service, for a period of three (3) years
from the date of purchase by the consumer. If at any time during the warranty period the
product is determined to be defective or malfunctions, Aube shall repair or replace it (at
Aube's option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which
you purchased it, or
(ii) contact Aube. Aube will make the determination whether the product should be
returned, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not
apply if it is shown by Aube that the defect or malfunction was caused by damage which
occurred while the product was in the possession of a consumer.
Aube's sole responsibility shall be to repair or replace the product within the terms stated
above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS
OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces and
states do not allow the exclusion or limitation of incidental or consequential damages, so
this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some
provinces and states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary
from province or state to another.
For more information on our products, visit us at
www.aubetech.com
s
Pre-programmed Schedule
6.
t
Modify the Schedule
7.
u
Advanced Programming
8.
Menus Default Options
PPd MO 4 0, 2, 4
PPd TU 4 0, 2, 4
PPd WE 4 0, 2, 4
PPd TH 4 0, 2, 4
PPd FR 4 0, 2, 4
PPd SA 2 0, 2, 4
PPd SU 2 0, 2, 4
CPH 5 2, 3, 4, 5, 6
HLd 10°C 5°C to 28°C
ES OF (off) OF / ON
PP OF (off) OF / ON
Time you wake
up and desired
temperature
Time you leave
and temperature
during your
absence
Time you return
home and
desired
temperature
Time you go to
bed and
overnight
temperature
Cycles/hour Length Installation
2 30 min. Commercial unit
3 20 min. Commercial unit
4 15 min. Fuel, gas & electrical furnace
5 12 min. Direct wiring to circulator
6 10 min. Direct wiring to circulator
v
Technical Specifications
9.
;
Warranty
10.
Technical Assistance
11.
705 Montrichard
Saint-Jean-sur-Richelieu
Québec, Canada J2X 5K8
Tel. : (450) 358-4600
1-800-831-AUBE
Fax : (450) 358-4650
aube.service@honeywell.com
10 rue Ampère
95500 Gonesse
France
33 (0) 1 34 07 99 00
33 (0) 1 34 07 99 19
advaube@comintes.com
400-136-001-C_ENG.fm Page 2 Friday, February 1, 2008 10:34 AM