Filter
Top Products
- 3 -
730237-100 REV. Q
9
11
10
CONNECT WATER SUPPLY
a. Connect water supply line between
shutoff valve and tank water inlet
fitting. Tighten COUPLING NUT 1/4 turn
beyond hand tight. Check that refill tube
is inserted into overflow tube.
b. Turn on supply valve and allow tank to
fill until float rises to shutoff position.
c. Check for leakage at fittings, tighten or
correct as needed.
d. Do not use plumber's putty to seal
these fittings.
ADJUSTMENTS
a. Flush tank and check that tank fills and shuts off within 30 to 60
seconds, and tank water level is set as specified on tank rear wall.
b. To adjust water level: turn water level adjustment screw
counterclockwise to raise level; turn adjustment screw clockwise to
lower level.
c. To adjust flow rate (tank fill time): turn flow rate adjustment screw
clockwise to decrease flow rate (increase fill time); turn adjustment
screw counterclockwise to increase flow rate (decrease fill time).
d. Carefully position tank cover on tank.
e. The flush valve float has been factory set and does not require
adjustments. Repositioning of the float will change the amount of
water used which may effect the toilet's performance.
f. If bowl fails to siphon, an adjustment may be required with the lift chain.
Simply remove the bead chain from the retainment clip (see Fig. 10A)
and take up slack on the chain, and reinsert on lift rod. Make sure the
chain is not too taught.
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This
damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage
caused by the use of cleaners containing chlorine (calcium hypochlorite).
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify
when ordering.
Repair parts are determined by toilet tank number which can be
found marked inside tank.
PART NO.
4010
COMPACT
4092
COLONY
4037
RENAISSANCE
4310/4314/4392
COLONY/
COLONY AFTON
DESCRIPTION
TANK NUMBER
047242-XXX0A
047148-XXX0A
047192-XXX0A
738172-XXX0A
738170-XXX0A
738171-XXX0A
034783-XXX0A
738145-0070A
738372-0070A
738351-0070A
738462-0070A
738138-0070A
738356-0070A
047188-0070A
047158-0070A
738159-0070A
738165-0070A
TRIP LEVER
TRIP LEVER
TRIP LEVER
RIGHT HAND TRIP LEVER
RIGHT HAND TRIP LEVER
RIGHT HAND TRIP LEVER
BOLT CAP KIT (INCL 2 COVERS & WASHERS)
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
WATER CONTROL ASS'y W FLOAT BALL
FLUSH VALVE
FLUSH VALVE
COUPLING KIT, BOWL-TO-TANK
COUPLING KIT, BOWL-TO-TANK
FLAPPER ASSEMBLY
FLAPPER ASSEMBLY
TANK
COUPLING NUT
FLEXIBLE
SUPPLY
WATER INLET
COMPRESSION
COLLAR
WASHER
VALVE NUT
TRIM PLATE
VALVE
C L
TO RAISE
WATER
LEVEL
FLAPPER
ASSEMBLY
TO LOWER
WATER
LEVEL
TRIP
LEVER
FLUSH VALVE
WATER INLET
OVERFLOW
TUBE
FIG. 10A
WATER LINE
LEVEL
+
WATER CONTROL
ASSEMBLY
-
FLOW RATE
ADJUSTMENT
REFILL
TUBE
LIFT
ROD
FLOAT
BALL
FLUSH
VALVE
FLOAT
✔
✔
✔
✔✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
!
CAUTION: Overtightening of
COUPLING NUT could result in
breakage and potential flooding.