Filter
Top Products
730924-100 Rev. E
730924-100 Rev. E
730924-100 Rev. E
WAX RING
SEALANT
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install
wax ring evenly around waste flange, with tapered end of ring
facing toilet. Apply a thin bead of sealant around toilet base.
- 3 -
730924-100 Rev. E
- 2 -
- 4 -
- 5 -
S A V E F O R F U T U R E U S E
730924-100 Rev. E
Pr odu ct nam es lis ted herein are trademarks of American Standard Inc.
© Ame ric an Sta nda rd Inc. 2007
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant
Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or
Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Model 2073 FloWise
™
Normal Height
Elongated High Efficiency Toilet
FloWise
™
HET TEN-YEAR WORRY-FREE
™
LIMITED WARRANTY
For this warranty to become effective, the accompanying warranty registration card and proof of purchase must be completed and
returned to the address on the warranty registration card within 30 days of purchase.
If inspection of this American Standard plumbing product, inclusive of china and all mechanical components, within ten years after its
initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the
product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this
product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it
has been modified in a manner inconsistent with the product as shipped by American Standard.
This warranty DOES NOT COVER any damage caused by the use of in-tank cleaners.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or
installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a
product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some
states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to
province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product
was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard-us.com
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
5
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP" must face up!
6
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to size
before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
!
7
14
9a
Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in water
leakage. Water supply tube or
pipe must extend at least 1/2"
inside threaded shank of valve
(does not apply to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not seal
completely on spiral
type supply line.
Captive cone washers
already included. No
additional washers needed.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
INSTALL TANK
a. Install large rubber gasket over threaded outlet on bottom of tank and
lower tank onto bowl so that tapered end of gasket fits evenly into bowl
water inlet opening, and tank mounting bolts go through mounting holes.
Secure with metal washer/nuts.
b. With tank parallel to wall, alternately tighten hex nuts until tank is
snugged down evenly against bowl surface.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
DO NOT SPIN BOLTS WITH SCREWDRIVER
IMPORTANT: Always clear
sand and rust from system.
Make sure water supply is off.
Remove valve TOP by lifting arm
and rotating top and arm 1/8 turn
counterclockwise, pressing down
slightly on cap.
While holding a
container over
the uncapped VALVE to
prevent splashing, turn water
supply on and off a few times.
Leave water supply off.
Replace TOP by engaging lugs
and rotating 1/8 turn clockwise.
MAKE CERTAIN TIP IS
TURNED TO THE LOCKED
POSITION. VALVE MAY NOT
TURN ON IF TOP IS NOT
FULLY TURNED TO THE
LOCKED POSITION.
For troubleshooting information please contact:
Manufacturer's First Year Fill Valve Warranty:
TROUBLESHOOTING FILL VALVE
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 14.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because:
• The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided.
• The flush valve is leaking because it's worn, dirty or misaligned (replace seal or flush valve).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster
Model 242 Replacement Seal may be needed.
© 2001 Fluidmaster, Inc.
® Registered trademark of Fluidmaster, Inc.
GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year.
Units returned to Fluidmaster will be replaced without charge.
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or
liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc.
See next page for FloWise™ Ten-Year Worry-Free™ Limited Warranty.
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
(949) 728-2000 (800) 631-2011
www.fluidmaster.com
1
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
REMOVE OLD TOILET
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
RUBBER
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
WASHER/NUT
CLOSET BOLT
NUT
WASHER
BOLT CAP
CLOSET FLANGE
Does not flush
Poor or sluggish flush
Toilet leaks
Toilet does not shut off
a. Water supply valve closed.
b. Supply line blocked.
c. Flush valve chain too loose or disconnected.
d. Sand or debris lodged in water control.
a. Bowl water level too low.
b. Supply valve partly closed.
c. Partially clogged trapway and/or drain pipe and/or vent.
d. Supply pressure too low.
a. Poor supply line connection.
b. Poor bowl to tank/floor connection.
a. Flush valve chain too tight, holding flush valve open.
b. Flush valve seal leaking or deformed.
c. Sand or debris lodged in water control.
a. Open valve and allow water to fill tank.
b. Shut off water supply, disconnect supply line and inspect all
gaskets and washers. Reassemble. Also, see Fluidmaster
maintenance. (see Step 14)
c. Readjust chain length as required.
d. Shut off water supply. Remove cap and clean as per Step 14.
a. Check that refill tube is connected to water control and
inserted into tank overflow without being kinked or damaged.
(see Step 13a)
b. Open supply valve fully. Be sure that proper supply tube size
is used.
c. Remove obstruction. Consult a plumber if necessary.
d. Normal supply pressure must be at least 20 psi.
a. Review Step 9 of installation procedure.
b. Review Step 4 through 7 of installation procedure.
a. Readjust chain length as needed. Review Step 10.
b. Clean debris from seal surface. Replace flush valve seal as
needed. (see Step 13)
c. Shut off water supply. Remove cap and clean as per Step 14.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
Repair parts are determined by toilet tank number which can be found marked inside tank.
PART NO.
DESCRIPTION
738611-XXX0A
034783-XXX0A
738565-424-0070A
7301111-0070A
3174.102-0070A
738985-0070A
738570-1000A
738756-0070A
735115-400-XXX
072989-0070A
TRIP LEVER
BOLT CAP KIT (INCL. 2 COVERS & WASHERS)
FLUIDMASTER 400A VALVE
FLUSH VALVE SEAL KIT
FLUSH VALVE ASSEMBLY
CLEVIS PIN ASSEMBLY
PVC REFILL TUBE
TANK TO BOWL COUPLING KIT #241
TANK COVER
CLIP FOR REFILL TUBE
Recommended fitting type for back-to-back installations.
Depending upon your plumbing and venting conditions, the flow
from the FloWise in a back-to-back installation may create a
vacuum on the system and draw water from the opposing bowl.
The National Standards Plumbing Code prohibits the use of a
cross fitting for drainage as throw over is possible. The code does
approve a directional "Y" style fitting with proper venting to direct
the water downward and away from the other toilet.
NOTE: BACK-TO-BACK INSTALLATION
ROUGHING-IN DIMENSIONS: Normal Height Elongated Two Piece Toilet
2
3
CLOSET FLANGE
CLOSET BOLTS
A
Recommended tool: Deep socket tool included in tank kit.
NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY.
THEY ARE NOT EXACT REPRESENTATIONS.
305mm
(12")
762mm
(30")
222mm
(8-3/4")
C/L OF OUTLET
FINISHED WALL
19mm ± 6mm
(3/4 ± 1/4")
381mm
(15")
C/L
470mm
(18-1/2")
C/L OF SEAT POST HOLES
140mm (5-1/2" CENTERS)
254mm
(10")
FINISHED
FLOOR
794mm
(31-1/4")
267mm
(10-1/2")
114mm
(4-1/2")
438mm
(17-1/4")
203mm
(8")
356mm
(14")
83mm
(3-1/4")
SUPPLY
AS
REQ'D
16mm
(5/8")
343mm
(13-1/2")
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90
°
, and slide
into place 6" (152 mm) apart and parallel to wall.
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
!
LIFT ARM
FIRST
109b
ADJUSTMENTS
a. Adjust water level. Water level should be adjusted to level indicated in
tank by adjusting float cup. See Step 11 for water level adjustment method.
IMPORTANT:
b. If bowl fails to siphon, an adjustment may be required with the lift chain.
Simply remove the bead chain from the retainment clip (see Fig. 10A)
and take up slack on the chain, and reinsert on lift rod. Make sure the chain
is not too taught.
With correct washers in place (see Step 9a), tighten
COUPLING NUT 1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
11
1. Turn off water supply and flush toilet to empty tank.
2. Disconnect chain from trip lever by removing hair pin cotter
and clevis pin.
3. Parially lift and support piston bottom with one hand.
4. Remove thumbscrew by turning counter-clockwise.
5. Remove piston top and gasket.
6. Replace gasket with new gasket.
7. Reverse procedure, turn thumbscrew until 2 clicks are felt.
TROUBLE SHOOTING FLUSH VALVE
SEAL REPLACEMENT:
NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE.
13
13a
REFILL TUBE REPLACEMENT:
12
When cleaning your toilet, wash it with mild, soapy water, rinse
thoroughly with clear water and dry with a soft cloth.
WARNING: Do not use in-tank cleaners. These products
can seriously damage fittings in the tank. This damage can
cause leakage and property damage.
American Standard shall not be responsible or liable for
any damage caused by the use of in-tank cleaners.
CARE AND CLEANING
!
Turn on water supply.
Submerge the FLOAT
CUP under the water for
30 seconds. Adjust the
water to desired level by
turning WATER LEVEL
ADJUSTMENT ROD
and moving FLOAT
CUP up or down.
Diagram 1
TANK
LEVER
REFILL
TUBE
TOP
ARM
NIPPLE
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
VALVE
BODY
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
FLOAT
CUP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
ADJUSTABLE
HEIGHT
LOCK NUT
Fig. 10A
WATER LEVEL
ADJUSTMENT
ROD
Locate bottom portion of
hose clip to vent tube at
location as shown.
THUMBSCREW
PISTON TOP
PISTON BOTTOM
GASKET
HAIR PIN
COTTER