American Standard 0475.920 Indoor Furnishings User Manual


  Open as PDF
of 2
 
J44
BARRIER FREE
© 2008 AS America Inc.
AQUALYN™
COUNTERTOP SINK
VITREOUS CHINA
FINISHED
WALL
OR
SPLASH BACK
441mm
(17-3/8)
518mm
(20-3/8)
175mm
(6-7/8)
71mm
(2-13/16)
102mm
(4)
OPTIONAL
C/L
FINISHED
FLOOR
1-1/4 O.D.
TAILPIECE
1-1/4 O.D.
WASTE
203mm
(8)
178mm
(7)
279mm
(11)
*
COUNTERTOP (BY OTHERS)
178mm
(7)
10mm
(3/8)
SEALING COMPOUND
SUPPLIES
AS REQ'D.
324mm
(12-3/4)
*
787mm (31)
854mm (33-5/8)
854mm
(33-5/8)
51mm
(2)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
FINISHED
WALL
OR
SPLASH BACK
441mm
(17-3/8)
518mm
(20-3/8)
175mm
(6-7/8)
71mm
(2-13/16)
102mm
(4)
114mm
(4-1/2)
OPTIONAL
C/L
FINISHED
FLOOR
1-1/4 O.D.
TAILPIECE
1-1/4 O.D.
WASTE
203mm
(8)
178mm
(7)
279mm
(11)
*
COUNTERTOP (BY OTHERS)
178mm
(7)
10mm
(3/8)
SEALING COMPOUND
SUPPLIES
AS REQ'D.
324mm
(12-3/4)
*
787mm (31)
854mm (33-5/8)
854mm
(33-5/8)
51mm
(2)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
79mm
(3-1/8)
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
FINISHED
WALL
OR
SPLASH BACK
441mm
(17-3/8)
518mm
(20-3/8)
175mm
(6-7/8)
71mm
(2-13/16)
102mm
(4)
114mm
(4-1/2)
OPTIONAL
C/L
FINISHED
FLOOR
1-1/4 O.D.
TAILPIECE
1-1/4 O.D.
WASTE
203mm
(8)
178mm
(7)
279mm
(11)
*
COUNTERTOP (BY OTHERS)
178mm
(7)
10mm
(3/8)
SEALING COMPOUND
SUPPLIES
AS REQ'D.
324mm
(12-3/4)
*
787mm (31)
854mm (33-5/8)
854mm
(33-5/8)
51mm
(2)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
79mm
(3-1/8)
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
NOTES:
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE
TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 51mm (2") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
0476.028 Faucet holes on 4" (102mm) centers 0476.037 Faucet holes on 4" (102mm) centers
• Extra right-hand hole
0475.035 Faucet holes on 4" (102mm) centers
• Extra left-hand hole
Revised 2/08
 previous