Filter
Top Products
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
1
2084796Rev. E 4/01
20" WALLMOUNT FAN
20" (50.8 cm) MODEL 4TM61C/9020C
OPERATING INSTRUCTIONS & PARTS MANUAL
DESCRIPTION
The AirKing 20" (50.8 cm) wallmount fan features 3-speed pull cord
operation and a 3-paddle fan blade. This fan has a permanently lubricated
motor with a 9 ft. (2.74 m) 18/3 cord set and is constructed of sturdy,
powder coated steel.
SPECIFICATIONS
Motor.......................................120V, 50/60 Hz
Blade diameter .......................20" (50.8 cm)
Speeds....................................3
Control ....................................Pull Cord
Air flow distribution .................360°
Approvals................................UL Listed. Close mesh fan guard
................................................
meets OSHA requirements.
WARNING: BECAUSE OF SIZE AND WEIGHT OF THIS FAN, MAKE
SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO
INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN FAN COMING
APART DURING OPERATION AND/OR PERSONAL INJURY.
WALL/CEILING BRACKET INSTALLATION
NOTE: ALWAYS INSTALL THE BRACKET TO A MINIMUM OF 2 X 4 STUDDING.
1. Lay Fan Head on flat surface, so the front side is facing down.
Loosely attach one Grill Knob and one Rubber Spacer to the Head
Assembly. Attach the other Grill Knob and Rubber Spacer to the
Head Assembly and FIRMLY tighten. Return to the first Grill Knob
and FIRMLY tighten. (Figure 1)
GENERAL SAFETY INFORMATION
1. Make certain that the power source conforms to the electrical
requirements of the fan.
2. The power cord is equipped with a three-prong grounded plug that must
be inserted into a matching receptacle. Under no circumstances must the
grounding prong be cut off the plug. Where a two-prong wall receptacle
is encountered, it must be replaced with a properly grounded three-prong
receptacle installed in accordance with the National Electrical Code
(NEC) and all applicable local codes and ordinances. This work must be
done only by a qualified electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS
NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE
THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS IS NOT
PERMITTED IN CANADA.
3. Where possible, avoid the use of extension cords. If they must be
used, minimize the risk of overheating by ensuring that they are UL
listed and of the proper gage and length. Never use a single extension
cord to operate more than one fan.
4. Do not insert fingers or foreign objects into the fan. Do not block or
tamper with the fan in any manner while it is in operation. Do not touch
the fan while in operation or just after it has been turned off, as some
parts may be hot enough to cause injury.
5. Unplug power cord before installing or servicing the fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE
SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR
SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.
6. This fan is intended for general use ONLY. It must NOT be used in
potentially dangerous locations such as flammable, explosive, chemical-
laden or wet atmospheres.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE.
7. DO NOT use fan in a window. Rain may create an electrical hazard.
8. Completely reassemble fan, according to instructions before
reconnecting to power supply.
Figure 2 (Wall Mount Assembly)
Fan Head
Nut
Wall Stud
Figure 3 (Ceiling Mount Assembly)
Fan Head
Bolt
2. Locate the wall or ceiling stud nearest to the desired Fan location.
Following the proper mounting diagram, attach the Bracket to the stud
using three (3) 5/16" diameter x 2" long Lag Screws (Not Supplied) or
appropriately sized Bolts and Nuts if attaching to "I" beams.
Wall Mount Assembly (Figure 2)
Ceiling Mount Assembly (Figure 3)
3. Insert Bolt through Yoke, Bracket, Pivot Hole, Flatwasher, and into
Locknut. (Figure 2) or (Figure 3)
4. While holding Fan in the desired position, firmly tighten the 7/16" Bolt.
Yoke
Bracket
Yoke
Bracket
Flatwasher
Pivot
Hole
Pivot
Hole
Flatwasher
Ceiling Stud
4
2084796Rev. E 4/01
MODELO 4TM61C/9020C
LISTA DE REPUESTOS
Ref No. de
Descripción Cant.
No. Parte
Cable de
Soporte
Secundario
Horqueta
Lazo Firme
en el Cable
Cola de 1"-2"
Figura 4 Figura 5
ADVERTENCIA: EL CABLE DE SOPORTE
SECUNDARIO QUE SE PROPORCIONA DEBE SER
USADO PARA SEGURIDAD ADICIONAL.
CABLE DE SOPORTE SECUNDARIO
1. Forme un lazo con el extremo del cable alrededor de la Horqueta. (Figura 5)
2. Coloque una Grapa de Cable con la "U" en la cola del lazo, dejando una
cola de aproximadamente 1 a 2 pulgadas. Apriete las tuercas de la grapa
a un esfuerzo de torsión de 32 pulgadas-libra, formando un lazo firme.
Asegúrese que ninguna parte del cable interfiera con la hélice. (Figura 5)
3. Envuelva el otro extremo del cable alrededor de una viga o armadura
segura del edificio, o de otro soporte cerca del Ventilador. Si ninguno de
ellos está disponible, envuelva el cable alrededor de la ménsula. (Figura 4)
Recoja las partes sobrantes del cable.
ADVERTENCIA: USE SOLAMENTE LOS ELEMENTOS
DE MONTAJE RECOMENDADOS PARA ESTE
VENTILADOR.
4. Coloque la Grapa de Cable restante, tal como se indica en el paso 2. El
exceso de la cola debe ser cortado de modo que se extienda 1 a 2
pulgadas más allá de la Grapa.
5. Verifique el conjunto para asegurar que la hélice esté libre de cualquier
obstrucción.
6. Enchufe el cable de conexión eléctrica dentro de un tomacorriente de tres
hojas conectado ampropiadamente a tierra. La unidad está lista para funcionar.
ADVERTENCIA: EL USO DEL CABLE DE SOPORTE SECUNDARIO NO
GARANTIZA LA PROTECCIÓN CONTRA LESIONES PERSONALES; EL
MONTAJE TANTO DEL CIRCULADOR COMO DEL CABLE PODRÍA
FALLAR SI SE LO SOMETE A ABUSOS, NEGLIGENCIA O INSTALACIÓN
NO APROPIADA.
OPERACIÓN
1.Conecte el cable y seleccione la velocidad de funcionamiento deseada con
el cordón accionador.
2. ADVERTENCIA: Este ventilador debe ser usa do solmente en unambiente
limpio y seco. Si producto esta montado de alguna otra manera espec´ifica que
indica la hoja de instrucción, purdiera anularse y no tener valor la garantia del
fabricante
MANTENIMIENTO
ADVERTENCIA: DESCONECTE SIEMPRE EL CORDÓN ANTES DE
INTENTAR REALIZAR CUALQUIER FUNCIÓN DE SERVICIO.
LIMPIEZA: Use un trapo y una solución de jabón suave, tal como detergente
líquido para lavar trastes.
ADVERTENCIA: No use gasolina, bencina, diluyente de pintura ni
limpiadores fuertes en aerosol, ya que éstos dañarán el ventilador.
ALMACENAMIENTO: Cuando no lo utilice, mantenga el aparato en un
lugar limpio y seco.
EL MOTOR HA SIDO PERMANENTEMENTE LUBRICADO.
******* Suministros por Bolso de Piezas Componentes Físicas (5098008)
Nut
Bolt
Commercial Style fan
WARNING:
This fan should be used only in a
clean, dry environment. Mounting of this product
in any way other than specified in the instruction
sheet will null and void the manufacturers warranty.
MODEL
4TM61C/9020C
SPEED
HIGH MED LOW
CFM 7510 5010 3735
M
3
/s 3.54 2.36 1.76
RPM 1560 1041 776
Amps 1.78 1.46 1.02
Watts 207 167 115
dB A 62 55 48
Grill Knob
Rubber Spacer
Rubber Spacer
Grill Knob
Figure 1
Yoke
14
12
11
10
13
8
7
5
6
2
4
3
11
10
18
17
16
15
20
19
21
22
23
25
24
25
24
8
1
9
26
26
1 2065510 Placa de Identificación 1
2 2050015 Cordón Eléctrico 1
3 2010636 Cubierta del Motor (Trasera) 1
4 2055001 Interruptor del Cordón Accionador 1
5 ******* Cordón Accionador con Colgante 1
6 2090552 Tuerca para el Alambre 2
7 5096037A Rejilla Trasera 1
8 2091126B Tornillo de #6 x 5/8 Tipo 25 PTH 3
9 2030021SB Motor 1
10 ******* Perilla de la Rejilla 2
11 ******* Espaciador de Caucho 2
12 2011604 Horqueta 1
13 5082075BK Hélice 1
14 5090044 Tornillo Prisionero de 1/4-28 x 3/8" 1
15 ******* Perno de 7/16" -18 x 5" (Negro) 1
16 ******* Arandelas Planas 7/16" (Negro) 1
17 2060016 Soporte 1
18 5096038A Rejilla Delantera 1
19 2091143 Tornillo de #8 x 3/8 Tipo F PPH 8
20 2070004A Ojo de Buey 1
21 ******* Cable de Seguridad 1
22 ******* Grapa de Cable 2
23 ******* Tuerca de Seguridad 7/16-18 1
24 2091162 Tornillo de #8 x 1/2 Tipo F PPH 4
25 5060016 Placa de Pivote con Hexagonal 2
26 5090045 #10-32 x 1/2 HWH SERR F-ZP 3