Filter
Top Products
AIPHONE
CO.,
LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A., WISSOUS, CEDEX, FRANCE
Camera
angle of view
AIPHONE"
Horizontal angle
of
view Vertical angle
of
view
71.5" 53.4"
+Wiring
0
SDeaker switchina
0
Sensor sensitivity switching
0
Operation indicator light (LED) switching
The operation indicator light select switch can switch
the operation indicator lights ON/OFF. The normal
setting is
"OFF".
Switching
OFF
the operation indicator
light avoids making visitors aware that they are being
photographed by the camera.
f
p/screw cover
The sensor sensitivity select switch can switch the
sensitivity with which people are detected among three
levels. Set
this
switch
to
match the environment.
CAUTION
~
Before turning on
the
power,
make
sure
wires
are not wrongly
connected or shorted.
Fire or electric
shock could result.
@
Speaker
Make sure the speaker select switch is
always on
"OFF"
side.
c
0
*Cover mounting screw
Remove the screw cover and loosen the cover mounting screw.
Pull the top of the
two
sides of the main unit cover toward you
and remove the main unit cover.
wiring.
Do
not install with wet or damp
hands.Electric shock could result.
The factory setting is "M"
,,,,,,,
H (High): This raises the
Sensor
sensitivity. (Set this
if
detection is difficult.
position.
sensitivity. (Set this
if
the system is
frequently triggered by
mistake.)
M (Medium): Normally, use this
L (Low): This lowers the
%
This
does not change the sensitivity of
a
sensor connected
directly to the external sensor input.
Speaker
bij
c
ON:
The LED lights up when
The factory setting is
"OFF"
LED
AND/OR
a person is detected. It
lights
UD
for
amrox.
2
External
sensor
input
sgc. (Used foi area
adjustment.)
OFF: The LED does not light
up. (This is the normal
position for use.)
0
Internal sensor switching
Speaker
The internal sensor can be switched
ON/OFF by
the
main unit's internal
sensor select switch.
Use
this
when the internal sensor is
not necessary, for example when
0
using an external sensor.
The sensor sensitivity varies with the temperature
and
this
can cause mistaken detection. Set the
sensitivity according to the season
as
follows.
Summa
->
H
(High)
Spring,
Autumn
(Medium)
Winter
o
L
&ow)
A
-
c
The factory setting is
"ON".
ON:
The internal sensor
detects people.
OFF:
The internal sensor does
Internal sensor
CAUTION
I
Loosen the lock screw, pull the main unit bottom toward
you, and remove the main unit from
the
mounting plate.
Do
not pull the cover out more than is necessary.
It may result disconnection at cable.
,
-
not detect people.
0
Mic. sensitivitv
Mount with
this
lllll
I
The internal mic. enables
the
user
to
hear outside
sounds from the master station. The volume can be
adjusted with the mic. sensitivity volume.
0
Master station switchina
1
Mic. sensitivity
I
I
1
I
Speaker
You can switch the master station
The factory setting is "B".
B:
JA series
iI
li
I1
II
I
Mic. Sensitivity
The factory setting is "Medium".
High: Raises the volume.
Low: Lowers the volume.
111
i
Low
49-
''
High
1
Internal sensoi
Wire
the master station with PE (polyethylene) insulated wire with
PVC
jacket.
Refer to the table below for wire diameters and permitted wiring distances.
ISingle core wire1
0
0.65
mm
1
0
0.9
mm
1
0
1.2
mm
1
Internal sensor
When mounting
on
an outside wall with a large gap or on
an uneven surface, such as tiles, fill in the mounting surface
grooves and gaps with caulk.
1
Peel approx.
7
mm
of insulation
off
the ends of wires.
Distance
150
meters ma.
1
100
meters ma.
1
100
meters ma.
1
0
External sensor input function
Tear the wall sponge at
the
mounting plate wiring hole
section and pull the
wires
through from inside the wall.
Mount the mounting plate at the prescribed position.
%
Caulk around the
wires
before mounting the main unit.
The external sensor input function connects a separate sensor to
this
unit's external sensor input to widen the
detection range and improve the reliability of detection performance. For
the
external sensor unit, connect one
with N.C. type (normally closed) output.
The factory setting is
0
set.
0
OR
mode
When a person enters the detection area of
this
unit or external sensor, the sensor detects
this
and their picture
is talren.
Since
this
mode is triggered by entry to either one of
the
detection areas, it can widen
the
detection area.
When not connecting an external sensor, set to
this
position.
%When connecting an external sensor, install it somewhere that the camera on
this
unit can photograph
anyone who enters that external sensor's detection area.
%When not connecting an external sensor, use "OR mode".
A
ppprox.
7
mm
+
If
the
waterproofing is incomplete,
this
can cause
equipment breakdown,
fire,
or electric shock.
+
When surface cable runs are necessarv
@AND
If
someone
mode
is detected by either
this
unit or the external sensor, then is detected by the other sensor within 30
sec., that person is detected and photographed.
(If someone passes through only one detection
area,
even
if
hdshe then passes
through
the other detection
area
more than 30 sec. later, hdshe is not detected.)
Since the detectors do not detect
if
a person, a cat, or whatever passes through only one of the detection
areas,
this
is an effective measure against mistaken detection.
m
Detection area for this unit@
/
Speaker
Speaker
\
/
/External sensor
Mounting plate
e
Internal sensor
@
and
@
:
The person is detected and photographed.
only
@
,
or only
@
:
Does not detect.
External sensor
detection area
@
Mount the unit onto the frame, then tighten down the lock
screws.
Next, adjust the camera and sensor.
For details, refer to
"ADJUSTMENTS".
I
7
Connect
the
necessary wires.
%See
the
"Wiring diagram".
After that, fill in the gap at the wiring hole section.
@
:
The person is detected and photographed.
@
:
The person is detected and photographed.
Cut out the knockout at
the
bottom of
the
mounting plate and wire the
required wires to the main unit side.
+Installation precautions
I
OAdiustinrr the camera direction:
I
@When the camera and
I
+Detection area and camera angle
of
view
Plain diagram
(0"
left-right swing)
Side diagram
(m)
(upldown swing
0')
EZ
Sensor detection area
2
1
0
1
2
3
4
5
6
7(m)
-
Thi
camira moves
50"
to the left and to the right.
(It moves in
5"
by a step.)
The
camera moves
35"
down.
(It moves in
5"
by a step.)
@Adjusting the sensor direction:
The
sensor moves
50"
to the left and
to
the right.
(It moves in
10"
by a step.)
The
sensor moves
35"
down.
(It moves in
5"
by a step.)
-
sensor adjustments are
complete, put
the
main unit
cover on securely from the
front and tighten down
the
main unit cover mounting
screws.
Sometimes a person
'
approaching the detection
area from directly in front
of the camera is diflicult
to detect. (Figure A)
EZ
Sensor detection area
range
Side diagram
I
ACaution:
Adjust the sensor direction with holding the
plastic knob on the top of the sensor, N(YT with
touching the reflector plate or P.C. board of the
sensor. Touching the sensor with wet or damp
hands, could cause malfunction or breakdown.
(downward swing
25")
EZ
Sensor detection area
Mount
so
that persons
cut across the detection
area.(Figure
B)
Figure
B
11
I,,
, ,
:\,
I
0
1
2
3
4
5
6
7(m)