Filter
Top Products
Remote Control
1. INTRODUCTION
Model 4B-101
2. LEARN REMOTE CONTROL TO AAA+
TM
CONTROL PANEL
The Remote Control allows you to operate the AAA+
TM
control panel
remotely with a press of a button. You can arm the system, disarm the
system and activate the alarm instantly. You also have the option to use
this remote to operate other devices such as a garage door receiver.
In this package, you should find a remote control, with a 12V alkaline
battery installed.
Please follow the instructions below to program the remote control to the
AAA+
TM
control panel.
12V alkaline battery
(installed)
In order for the remote control to communicate with the control panel
properly, the remote must be programmed to the control panel. Follow
the brief instructions below or refer to the detail instructions from the
AAA+
TM
User’s Instructions to program the remote control to the control
panel.
Remote controls should be programmed to Device 6 to Device 0 on the
AAA+
TM
control panel.
Follow the instructions below to program remote(s) to remote location(s)
6, 7, 8, 9, or 0, which is the bottom row of the numeric keypad of the
control panel.
Remote
Control
4
[PROG]
[MPIN]
Enter Program-
ming mode
Enter master
password to
programming
mode
3 beeps for valid
password. 1 long
beep for invalid
password.
[4]
Select learn
remote
programming
[6] to [0]
After you have
selected the remote
location, that zone
LED will be on.
Activate remote
After [4] is entered,
some zone LEDs will
flash or stay off. The
zone LEDs represent
whether that zone is
already occupied by
another remote.
**See Table A below.
Select remote
location
(Max. 5
remotes)
Select a remote
location [6], [7],
[8], [9] or [0].
Once the signal is
transmitted to the
Control Panel, that
signal which will be
stored.
You will hear [Device
X Accepted ], where
“X” is the remote
location.
Activate the
remote by
pressing any
one of the
buttons.
Step Keys Function Description Note
1
2
3
ZONE LED DESCRIPTION
Off Zone is not occupied by any remote
Flashes twice This zone is occupied by another remote. Programming
another remote to this zone will overwrite the previous
remote.
Flashes once This zone is occupied by a control module (Optional).
You can still program a remote to this zone, and it will not
overwrite the control module you have in this zone.
Flashes once, This zone is occupied by a remote AND a control module.
then twice If you program another remote to this zone, it will overwrite
the previous remote, but not the control module.
** Table A: Zone LED status for learning remote control(s).
2. LEARN REMOTE CONTROL TO AAA+
TM
CONTROL PANEL (CONT)
Remote [6] is represented by zone LED 1
®
ZONE
LED
1 6
2 7
3 8
4 9
5 0
REMOTE
LOCATION
3. OPERATION
The remote can be used to arm, disarm, activate the alarm instantly, plus
control one additional device.
Arm - Pressing the arm button on the keychain remote will arm the system,
which will result in a 45-second exit delay. Arm LED will also be on.
Disarm - Pressing the disarm button on the keychain remote will disarm
the system instantly. Arm LED will also be off.
Panic - Pressing the panic button will cause the siren to sound instantly
and outgoing calls will be made to the preprogrammed phone numbers.
AUX - This button can be used to operate other Skylink’s devices (sold
separately), such as a garage door receiver, which can be used to open
/ close a garage door.
PANIC
ARM
DISARM
AUX
4. BATTERY REPLACEMENT
The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to
be replaced when either one of the followings occurs:
1. The LED on the keychain doesn’t flash or on when a key is pressed; or
2. The operating range starts to decrease.
To replace the battery:
1. Undo the two screws on the back of the
transmitter.
The bottom case will then come off.
2. Using a small screwdriver or pen, pry out
the old battery from one end.
3. Place the new battery in position. A diagram
in the battery compartment indicates which
end is positive and which is negative.
4. Close the battery cover and reinsert
two screws.
+
-