Filter
Top Products
1. INTRODUCTION
Model 18K
In this package, you will find a keyless entry transmitter with 3V lithium
batteries and screws.
Keyless Entry Transmitter
(Batteries inside)
Skylink
®
Keyless Entry Transmitter
3. TROUBLE SHOOTING
Q: Door opener does not react after pressing the button on the transmitter.
A:- Ensure you hear 3 beeps from the keypad transmitter after entering
the default PIN [0,0,0,0], [#], [1],. If you do not hear 3 beeps, that means
the PIN you entered is incorrect. Re-enter the correct PIN.
- If the red light on the receiver flashes after entering the PIN on the
transmitter, but the door opener does not respond, please ensure the
red/black wire is successfully connected from the receiver to the
wall mounted door control.
- Ensure the wires that are previously connected to the wall mounted
door control are not loose.
- Ensure the keypad transmitter has been programmed to the receiver.
Refer to section 2 for how to program a keypad to the receiver.
2. PROGRAM A KEYPAD TO THE RECEIVER
You need to do the programming in order to add the keypad transmitter
to the receiver.
Plug the receiver 18R (sold separately) into an electrical socket.
Press and hold the learn button at the left hand side of the receiver.
The red LED on the receiver will flash.
1
2
5. KEYPAD OPERATION
The backlight comes on and a beep is emitted when any key is pressed. The
backlight of the keypad may not be visible when it is too bright outside. When
any key is pressed, the next key must be pressed within 5 seconds or the
backlight turns off and the sequence is cancelled. You must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds
and press the key again.
For example, if you are changing the PIN number from 0000 to
123456, enter the following sequence, 0000, ,123456, ,123456, .
If confirmed, the backlit LED flashes and the unit emits a long beep.
***
If you do not hear 3 beeps after the 4-digit PIN, [#] and [assigned door
number] is entered, that means you have entered an incorrect PIN, and the
keypad transmitter will not operate your garage door.
Two 3 volt Lithium type (CR2032)
batteries (included).
It is time to change
the batteries when
the backlight no
longer appears.
+
-
Battery Compartment
7. BATTERY
4. REMOVE TRANSMITTER FROM THE RECEIVER
Press the [4-digit PIN], [#] and [the assigned
number of the door] within 5 seconds. The
assigned door number can be either 1, 2, 3 or 4.
Example: [0][0][0][0][#][3], for door 3.
The receiver red LED will go off indicates the
programming is completed.
To program the keypad to control more than
one receiver, repeat process (1) to (4) with
different assigned door numbers.
3
4
5
Learn Button
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
10. WARRANTY
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
11. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com , or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
8. ADDITIONAL RECEIVER
You can use 18K to control up to 4 garage door openers by adding
Skylink
®
Garage Door Receiver 18R for each opener.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A290-001 Rev.1
©2004 SKYLINK GROUP
Follow the instructions below to change the PIN.
To change your PIN:
1. Enter the current PIN, (factory default PIN 0 0 0 0), press ,
2. Enter new 4 to 6 digit PIN, press ,
3. Enter new PIN again, press .
*
*
*
6. CHANGE PIN
You can delete the transmitter from a receiver.
Unplug the receiver from the electrical socket.
Press and hold the learn button on the left hand side of the receiver
when plugging the receiver into an electrical socket, the red LED on the
receiver will flash rapidly. All the transmitters and keypads are deleted.
2
1
1 pc 2.6 x 6 screw
1 pc 2.6 x 12 screw
1 pc 2.6 x 25 screw
You can now mount the transmitter on a
desired location.
Lift up the cover and insert screw
above the keypad in the slot provided (a).
Remove the battery cover and insert
the second screw in the lower slot (b).
Tighten all screws. Replace the battery
cover, insert and tighten screw (c).
(a)
(c)
(b)
6