Filter
Top Products
©2007. RadioShack Corporation.
All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
09A07
49-118
Printed in China
Wireless · Key-Lock
DOOR/WINDOW ALARM
Setting Up Your Alarm
Thank you for purchasing your Door/Window
Alarm from RadioShack. Please read this user’s
guide before installing, setting up and using
your new door/window alarm.
www.radioshack.com
What’s Included
Alarm Magnet
Key (2) Adhesive Strip (3)
Screw (4) Anchor (4)
Drilling Template User’s Guide
Actual product may vary from the images
found in this document.
Battery Notes:
• Dispose of old batteries promptly and
properly. Do not burn or bury them.
• Use only fresh batteries of the required
size and recommended type.
• Do not mix old and new batteries,
different types of batteries (standard,
alkaline, or rechargeable), or rechargeable
batteries of different capacities.
• If you do not plan to use the alarm for
a month or more, remove the batteries.
Batteries can leak chemicals that can
destroy electronic parts.
49-118
Mounting Your Alarm Using Screws
1. Use the supplied drilling template to mark
the mounting screw location.
2. Drill two
1
/
16
- inch (2 mm) holes.
3. Insert the top screw, leaving about
1
/
8
- inch
(3 mm) to engage the keyhole on the alarm.
4. Install the alarm over the top screw.
5. Slide off the battery cover.
6. Insert the lower screw through the hole inside
the battery compartment.
Using Your Alarm
Instant Activation
1. Slide INSTANT/DELAY switch to INSTANT.
2. Insert key and rotate to ON.
3. If you move the magnet away from the alarm, it sounds for
about 90 seconds. Then, the alarm turns off and the LED
flashes green. Turn the key to OFF if you want to silence the alarm immediately.
Delay Activation
1. Slide INSTANT/DELAY switch to DELAY.
2. Insert key and rotate to ON. The LED lights green and you have 15 seconds to
leave and close the door. After 15 seconds, the alarm arms and the LED turns off.
Deactivation
1. When you return home and open the door, the LED lights red and you have 10 - 15
seconds to turn off the alarm.
2. Turn the key to OFF to disarm. If you do not disarm it, the alarm sounds for 90
seconds.
3. If the alarm was triggered while you were away, the LED alternately flashes green
and red after the alarm has sounded for 90 seconds.
Choosing a Location
1. Align the triangle on the magnet with the
engraved line on the left or right side of the
alarm.
2. Place the magnet edge no more than
5
/
16
- inch (8 mm) from the alarm.
3. Mount the alarm to a door or window and
the magnet to the door or window frame
using the supplied adhesive strips or screws.
Installing Batteries
1. Remove the screw on the bottom of your
alarm and lift the battery compartment cover.
2. Insert two AAA
batteries (not
supplied), as indicated
by the polarity
symbols (+ and -)
marked inside.
3. Replace the cover.
4. Replace the batteries if the alarm sound
weakens or the LED flashes red. If the alarm
does not work after you replace the batteries,
remove and reinstall them.
Mounting the Magnet
1. Use a small, flat bladed screwdriver to
remove the mounting plate from the magnet.
2. Use the supplied screws or adhesive strips
to secure the mounting plate to the selected
surface. Do not use both strip and screws.
3. Connect magnet to mounting plate.
Apply to frame
Mounting
Plate
Magnet (Rear View)
5
/
16
“ max
Battery
Cover
Drilling
Template
LED
Alarm
Adhesive Strip (3)
Keys
Magnet
Anchor (4)
Screw (4)