Lux Products TX9000A Thermostat User Manual


  Open as PDF
of 1
 
Push in the RESET key. This sets the
built-in heating and cooling programs.
To review the built-in programs,press
NEXT or PREVIOUS repeatedly; when
you are done, press RETURN.
You can use the built-in programs as
shown, or change them as you wish.
Each day is divided into four periods.
Each period has its own starting time
and temperature.
TEMPERATURE SWING
A thermostat works by turning your heating or cooling system on and off whenever the room
temperature varies a certain number of degrees from the set-point temperature. This variation is the
“swing.” Your system should cycle on about 3 to 6 times per hour. A smaller swing number increases
the number of cycles, so room temperature is more constant. A larger swing number decreases the
number of cycles, to save energy in most cases.
• The Unit can be
used with most
24 volt gas, oil or
electric heating
and air conditioning
systems, single-stage
heat pumps or gas
millivolt heating systems.
It cannot be used with 120
volt heating systems or
multistage heat pumps. Ask
your dealer for other LUX
thermostats to control
those systems.
•
The Unit is programmable.
There are four programming
periods per day. Each
period can be programmed
separately.
• You can use the built-in
time/temperature
programs, or alter them
to suit your schedule. The
Unit provides separate
programming for every day
of the week- for both heating and cooling. You can override the programmed temperatures for as
little as one programming period or for an entire vacation.
• In cool weather, when the system switch is set to HEAT, the Unit will maintain cooler “set back”
room temperatures to save energy. It will then change to warmer “comfort” settings — all
automatically, at specified times during the day.
• In warm weather, when the system switch is set to COOL, the Unit will maintain warmer “set
back” room temperatures to save energy. It will then change to cooler “comfort” settings - all
automatically, at specified times during the day.
• A large liquid crystal display shows time, day of the week, and room and set temperatures.
It will remind you when the filter should be changed in your blower and track your system’s energy
usage.
• Temperature swing adjustment lets you fine-tune your system for maximum comfort and
economy.
• 5/2 Minute Selectable Minimum Run/Off Time for Short Cycle/Compressor Protection.
• Two Energizer® or DURACELL® “AA” alkaline batteries (not included) are used to retain your
time and temperature programs.
LUX PRODUCTS CORPORATION • Mt. Laurel, New Jersey 08054 USA
INSTALLATION
IMPORTANT!
Thank you for your confidence in our product. To obtain the best results from
your investment, please read these instructions and acquaint yourself with
your purchase before installing your new thermostat. Then follow the
installation procedures, one step at a time. This will save you time and
minimize the chance of damaging the thermostat and the systems it controls.
These instructions may contain information beyond that required for your
particular installation. Please save for future reference.
READ
INSTALLATION
INSTRUCTIONS
FIRST
Please read all instructions carefully
before beginning installation.
TOOLS REQUIRED
#1 Phillips screwdriver (small)
Drill with 3/16-in. (4.8mm) bit
THERMOSTAT LOCATION
On replacement installations, mount the
new thermostat in place of the old one unless the conditions listed below suggest otherwise. On new
installations, follow the guidelines listed below.
1. Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and in a room that is
used often.
2. Do not install it where there are unusual heating conditions, such as: in direct
sunlight; near a lamp, radio, television, radiator, register, or fireplace; near hot water pipes in a wall;
near a stove on the other side of a wall.
3. Do not locate in unusual cooling conditions, such as: on a wall separating an unheated room; or in
a draft from a stairwell, door, or window.
4. Do not locate in a damp area. This can lead to corrosion that will shorten thermostat life.
5. Do not locate where air circulation is poor, such as: in a corner or an alcove; or behind an open
door.
6. Do not install the unit until all construction work and painting has been completed.
7. This thermostat does not require leveling.
CAUTION
To avoid electrical shock and
to prevent damage to the
furnace, air conditioner, and
thermostat, disconnect the power
supply before beginning work. This
can be done at the fuse box, at the
circuit breaker, or at the appliance.
OFF
REMOVING THE OLD THERMOSTAT
Switch electricity to the furnace and air conditioner OFF; then
proceed with the following steps.
1. Remove cover from old thermostat. Most are snap-on types and
simply pull off. Some have locking screws on the side. These
must be loosened.
2. Note the letters printed near the terminals. Attach labels
(enclosed) to each wire for identification. Remove and label wires
one at a time. Make sure the wires do not fall back inside the
wall.
3. Loosen all screws on the old thermostat and remove it from the
wall.
MOUNTING THE UNIT ON THE WALL
1. Strip insulation 3/8 in. (9.5mm) from wire ends and clean off any corrosion.
2. Fill wall opening with non-combustible insulation to prevent
drafts from affecting the thermostat.
3. Press up on the button on bottom of thermostat and swing the
body away from the base and up to remove the body from the base.
CAUTION
Read instructions carefully
before removing any
wiring from existing
thermostat. Wires must be
labeled before they are
removed. When removing
wires from their terminals,
ignore the color of the
wires since these may not
comply with the standard.
CAUTION
Do not allow wires to touch each other or parts on thermostat. Wires must be
trapped between black spacer and brass terminal. Also, be sure to tighten securely
all 7 electrical terminal screws.
NOTE
If you are mounting the base to
a soft material like plasterboard
or if you are using the old
mounting holes, the screws
may not hold. Drill a 3/16-in.
(4.8mm) hole at each screw
location, and insert the plastic
anchors provided. Then mount
the base as described below.
FILTER USAGE MONITOR
The FILTER Monitor counts the hours since the filter in your blower was last changed. After 250
hours of use, FILTER will appear in the display. After you change the filter, set the thermostat’s FILTER
Monitor back to zero as follows.
CAUTION
• Your thermostat is a precision instrument. Please handle it with care.
• Turn off electricity to the appliance before installing or servicing thermostat or any
part of the system. Do not turn electricity back on until work is completed.
• Do not short (jumper) across electric terminals at control on furnace or air conditioner
to test the system. This will damage the thermostat and void your warranty.
• All wiring must conform to local codes and ordinances.
• This thermostat is designed for use with 24 volt and millivolt systems. The thermostat
should be limited to a maximum of 1.0 amps; higher amperage may cause damage
to the thermostat. If you are in doubt, call your utility company.
TEMPERATURE CALIBRATION
SWING SETTINGS
PROGRAM LOCK
CHANGING FROM °F TO °C AND A 12HR CLOCK TO A 24HR CLOCK
TECHNICAL SERVICE
If you have any problems installing or using this thermostat, please carefully and thoroughly review the
instruction manual. If you require assistance, please contact our Technical Assistance Department at 856-
234-8803 during regular business hours between 8:00AM and 4:30PM Eastern Standard Time, Monday
through Friday. You can also receive technical assistance online anytime day or night at http://www.luxprod-
ucts.com. Our web site offers you answers to the most common technical questions, and also permits you to
email your questions to our technical support staff at your convenience.
WARRANTY
Limited Warranty: If this unit fails because of defects in materials or workmanship within three years of date
of original purchase, LUX will, at its option, repair or replace it. This warranty does not cover damage by acci-
dent, misuse, or failure to follow installation instructions. Implied warranties are limited in duration to three
years from date of original purchase. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. Please return malfunctioning or defective units to the par-
ticipating retailer from which purchase was made, along with proof of purchase. Please refer to "TECHNICAL
ASSISTANCE" before returning thermostat. Purchaser assumes all risks and liability for incidental and conse-
quential damage resulting from installation and use of this unit. Some states do not allow the exclusion of
incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state. Applicable in the
U.S.A. only.
THE BUILT IN ENERGY STAR
®
PROGRAMS
PERIOD HEAT COOL
MON-SUN
MORN 6:00 AM 70° 6:00 AM 78°
preprograms DAY 8:00 AM 62° 8:00 AM 85°
EVE 6:00 PM 70° 6:00 PM 78°
NIGHT 10:00 PM 62° 10:00 PM 82°
To change
current day.
Open the drop down door on the front of the thermostat. Rotate the dial to the SET DAY/TIME
position. You should see the display pictured above with a day of the week flashing. When you are
finished setting the day and time, rotate the dial to RUN to return to normal operation or to another
position to continue programming.
CAUTION
The unit is protected against normal static electric discharges. However, in extremely dry weather you
should touch another metal object before the unit to avoid potential loss of programs.
To change the
current time.
To set current time. The (e.g.
“12:00”) will be flashing.
The Unit alternately displays the current time
and the room temperature. It also displays the
day of the week and the currently active pro-
gram period that is controlling the temperature: MORN, DAY, EVE, or NIght.
The set point temperature will appear in the right side of the display. In the winter, set the system switch
to HEAT to control your heating system. In the summer, set the switch to COOL to control your air
conditioner. In spring and fall or when windows are open, you can set the system switch OFF.
Setting the FAN switch to AUTO automatically
runs your system’s fan during heating and cooling.
Setting the FAN switch to ON runs your system’s
fan continuously even without heating or cooling.
NOTE
The FAN switch works only if your system
provides a wire for the Unit’s “G” terminal.
Press UP/DOWN to change the current temperature setting. The OVERRIDE indicator
appears on display.
The Override feature will be automatically canceled at the start of the next program period.
To cancel OVERRIDE prior to next program period press UP/DOWN until original set tem-
perature appears. OVERRIDE indicator will disappear from display.
PROGRAMMING THE UNIT
You can change any preset times and/or temperatures to suit your schedules for the weekday,
Saturday and Sunday programs. Each period (Morning, Day, Evening, and Night) is programmed for
HEAT and for COOL.
Select HEAT to program the
unit for controlling your heater.
To program temperature.
To change the start
time for MORN.
To move to DAY.
To change the temp.
setting for MORN.
To program temperature.
To change start time
for DAY.
To move to EVE.
To change the temp.
setting for DAY.
To program temperature.
To change the start
time for EVE.
To move to NIGHT.
To change the temp.
setting for EVE.
To program temperature.
To change the start
time for NIGHT.
To change the temp.
setting for NIGHT.
Rotate dial to SET WEEKDAY PROGRAM. To program SATURDAY or
SUNDAY, rotate the dial to SET SATURDAY or SET WEEKEND PRO-
GRAM. With dial on SET WEEKDAY PROGRAM, you will see this display.
TEMPORARY TEMPERATURE OVERRIDE
VACATION TEMPERATURE HOLD
TX9000a SERIES
SMART TEMP
®
ELECTRONIC THERMOSTAT
Complete, Easy To Read Programming And Installation Instructions Inside
TEMPERATURE OVERRIDE AND TEMPERATURE HOLD
These features let you change the current Set Temperature without changing the programs stored in
your thermostat’s memory.
TEMP
TU
AM
MORN
HEAT
PROGRAM
FOR:
MO WETH FR
START AT:
SET TEMP
To change the FILTER Usage Monitor limit
To reset the counter
Rotate the dial to FILTER
To disable the FILTER Usage Monitor set the limit to 0 hours
To change the limit from 0-500 hours
Rotate the dial to SET DAY/TIME
Press together
To adjust the thermostat
To prevent tampering with set programs. The sequence of keys to lock and unlock the program:
Hold for two seconds
Rotate the dial to SET ENERGY/USAGE
Press together
ADVANCED FEATURES
DOWN
UP
WIRING DIAGRAMS
To change the temp. swing between 1-9 (4=approx.
±
1°F)
WARNING: Making these changes will require you to reset the thermostat. Copy any of your cus-
tomized programs onto the chart . This will be your reference to reenter the programs afterwards.
• 5/2 Minute Selectable Minimum Run/Off Time -J1.
• To change to Celsius - remove jumper -J2.
• To change to a 24HR clock - remove jumper- J3.
• Press the reset key on the front of the thermostat for changes to take effect.
• Reprogram as necessary.
Press to set.
Press HOLD. Adjust temperature as desired with UP/DOWN.
Temperature setting will not change even after next program period begins.
To clear, press HOLD again.
Select COOL to program the
unit for controlling your air conditioner.
OPERATION
This thermostat is “armchair programmable”
You can make any program or setting
changes with the thermostat body off or on
the wall thermostat base.
• Press UP/DOWN
to set time.
TO SET TIME & DAY
• Rotate Dial to SET
DAY/TIME.
• Press UP to change
current day.
• Press NEXT.
TO SET PROGRAMS
• Rotate Dial to SET
WEEKDAY,
SATURDAY or
SUNDAY PROGRAM.
• Press UP/DOWN to adjust
start time.
• Press NEXT.
• Press UP/DOWN to adjust
temperature.
• Press NEXT.
• Repeat as needed or rotate
dial to RUN to stop Programming.
TEMPORARY TEMPERATURE OVERRIDE
•Press UP/DOWN to adjust set temperatur
PATENT NO. 5,673,850
e.
•To clear OVERRIDE press UP/DOWN until
original set temperature appears or wait for
the start tf the next period.
TEMPERATURE HOLD
• Press HOLD. Adjust temperature as
desired with UP/DOWN.
•To clear, press HOLD again.
SIMPLIFIED INSTRUCTIONS
The Active Program Period
Liquid Crystal
Display
Fan
Switch
System
Switch
Easy to
follow
Instructions
LUX Speed
Dial
®
Thermostat
Body
The Set
Temperature
Thermostat
Cover
Button to Light Display
HEAT
OFF
COOL
AUTO
ON
FAN
RESET
HOLD
NEXT
RUN
FILTER
SET
SUNDAY
PROGRAM
SET
SATURDAY
PROGRAM
SET
WEEKDAY
PROGRAM
SET
DAY/TIME
DOWN
UP
1500
Patents Pending
M
O
D
A
Y
H
E
AT
P
M
SIMPLIFIED INSTRUCTIONS
•Press UP/DOWN to set time.
TO SET PROGRAMS
•Rotate Dial to SET
WEEKDAY
TEMPORARY TEMPERATURE OVERRIDE
•Press UP/DOWN to adjust set temperature.
•To clear OVERRIDE press UP/DOWN until
original set temperature appears or wait for
thestart tf the next period
TO SET TIME & DAY
•Rotate Dial to SET
DAY/TIME.
•Press UP to change
td
HEAT
OFF
COOL
AUTO
ON
FAN
RESET
HOLD
NEXT
RUN
FILTER
SET
SUNDAY
PROGRAM
SET
SATURDAY
PROGRAM
SET
WEEKDAY
PROGRAM
SET
DAY/TIME
DOWN
UP
1500
Patents Pending
M
O
D
A
Y
H
E
A
T
P
M
SIMPLIFIED INSTRUCTIONS
•Press UP/DOWN to set time.
TO SET PROGRAMS
•Rotate Dial to SET
TEMPORARY TEMPERATURE OVERRIDE
•Press UP/DOWN to adjust set temperature.
•To clear OVERRIDE press UP/DOWN until
original set temperature appears or wait for
TO SET TIME & DAY
•Rotate Dial to SET
DAY/TIME.
•Press UP to change
DOWN
UP
M
O
D
A
Y
H
E
A
T
P
M
Choose Heat or CoolSet Day & Time
Installs Easily
Easy as
1–2–3
INSTALLATION AND OPERATING INSTRUCTIONS
NEXT
UP
DOWN
NEXT
UP
DOWN
NEXT
UP
DOWN
NEXT
HOLD
NEXT
NEXT
HOLD
NEXT
NEXT
HOLD
NEXT
NEXT
UP
UP
UP
DOWN
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
NEXT
UP
DOWN
NEXT
UP
DOWN
NEXT
UP
DOWN
UP
DOWN
NEXT
NEXT
HOLD
CAUTION
Be careful not to drop the body or disturb electronic parts.
Leave the cover closed while the body is being removed from the base.
TERMINALS
SCREW
ANCHORS
BASE
W3 L
R
Y
O
GYWRHBORC
Attaching Wires
4. Hold the base against the wall, with the wires coming through wherever it
is convenient for wiring. Route the wires to below the terminal block.
Position the base for best appearance (to hide any marks from an old
thermostat). An optional wall plate is included for covering old mounting
holes. Attach the base to the wall with the two screws provided.
FEATURES
These diagrams below are provided for new installations or unreferenced wires.
1. Remove fresh batteries from their carton.
2. Remove body of thermostat as described at bottom of
first column.
3. Remove the battery clip and batteries.
4. Install two new Energizer
®
or DURACELL
®
"AA"
size alkaline batteries in the battery compartment.
Observe the polarity marking shown in the clip.
5. Place body back on the wall. Hook the
bottom of the body onto the base, swing the body up,
and snap the body onto the base.
Installation is now complete. Be sure to turn the power
back on to your heating and /or air conditioning system. If this is the first time you are installing batteries,
the thermostat will display “SUN 12:00 AM”. Within 90 seconds the thermostat will begin to display the
room temperature alternately with the time. To correct the display, see “Setting the TIME and DAY,” after
you set the programs.
REPLACE BATTERIES WHEN
INDICATOR APPEARS
CAUTION
The Unit is protected against normal static
electric discharges. However, in extremely
dry weather you should touch another
metal object before the Unit to avoid
potential loss of programs.
J4J3 J2 J1
2 MIN
C
24 HR
S/R ON
5 MIN
F
12 HR
S/R OFF
J1
J2
J3
J4
NOTE
When replacing batteries, you have
approximately 1 minute before programs are lost.
NOTE
If you have an electric system and the blower does not operate after installation, find the
electric/gas heat selector on the back of the body. Move the selector to the ELEC position.
OR
SETTING THE TIME OF DAY
NOTE
You must press “RESET” after enabling the features below. This will require you to
reprogram your thermostat. Please copy your programs into the blank chart provided
to assist reprogramming. Please reference the figure under “INSTALLING BATTERIES”
which shows the JUMPER LOCATIONS
SMART RECOVERY
Your thermostat has the capability to turn the HEAT and AIR CONDITIONING ON in your home so that it
reaches your desired comfort temperature at the time you have programmed. For instance, if you have pro-
grammed your thermostat for 70° at 5:00pm, normally the thermostat will begin to heat your home at 5:00pm.
With SMART RECOVERY on, the thermostat will calculate the best time to turn the heat on so that the temper-
ature in your home reaches 70° by 5:00pm. It calculates the amount of time through experience and will get
more accurate as time goes by. To enable SMART RECOVERY, remove J4 on the back of the thermostat. Press
the small reset button on the front of the thermostat. IN RECOVERY will appear in the display when this feature
is bringing your home to temperature.
The COPY button can be used to duplicate the
programs from any previous day.
Rotate dial to RUN position to start the programs or SET WEEKEND PROGRAM to continue
programming.
ENERGY USAGE MONITOR
A timer in the unit records your systems’s ON time for the current day, the previous day, and
cumulatively to let you see the effects of your temperature settings and weather conditions.
• Select HEAT to monitor heating energy usage or COOL to monitor cooling usage.
• Rotate the dial to SET ENERGY/USAGE
The current day’s ENERGY usage is displayed.
To reset the display to zero.
To display yesterday’s energy use.
NEXT
UP
To undo the previous reset to zero.
UP
To display total ENERGY usage since
the Monitor was last set to zero.
NEXT
Rotate the dial back to the RUN position.
WARNING: Use Energizer
®
or DURACELL
®
Alkaline Batteries Only
Energizer
®
is a registered trademark of Eveready Battery Company, Inc.
DURACELL
®
is a registered trademark of The Gillette Company, Inc.
WARNING: Use Energizer
®
or DURACELL
®
Alkaline Batteries Only.
INSTALLING BATTERIES
The Unit requires batteries to operate your furnace and retain its
programming in memory. Replace the batteries when the
REPLACE indicator appears in the display or at least once a year.
HEATING ONLY SYSTEMS COOLING ONLY SYSTEMS
4 -WIRES WITH ONE TRANSFORMER 5 -WIRES WITH TWO TRANSFORMERS
HEATING / COOLING SYSTEMS HEATING / COOLING SYSTEMS
YOGWBRHRC
OPTIONAL FAN WIRE
RC-RH JUMPER
PROVIDED
RH
RC
R
V
5
G
F
W
H
4
YOGWBRHRC
RC-RH JUMPER
PROVIDED
RH
RC
G
F
R
V
5
Y
C*
6
YOGWBRHRC
RC-RH JUMPER
PROVIDED
RH
RC
R
V
5
V
5
W
H
4
Y
C*
6
G
F
YOGWBRHRC
RC-RH JUMPER
PROVIDED
*CUSTOMER
SUPPLIED
JUMPER
RH
RC
R
Y
C*
G
F
YOGWBRHRC
RC-RH JUMPER
REMOVED
RH
V
5
TYPICAL SINGLE STAGE
HEAT PUMP WIRING
W
H
4
Y
C*
6
G
F
RC
R
O B
USE B or O NOT BOTH
TYPICAL HOOKUP FOR 2 OR 3 WIRE
24 VAC HEATING SYSTEMS (AND MILLIVOLT)
Y O G W B RH RC
Gas
Valve
or
Heater
FAN
System
XFMR
RH-RC JUMPER
PROVIDED
OPTIONAL
FAN LEAD
COMMON
TYPICAL COOL HOOKUP
24 VAC SYSTEMS
Y O G W B RH RC
FAN
A/C
Comp.
System
XFMR
RH-RC JUMPER
PROVIDED
SYSTEM
COMMON
TYPICAL 24 VAC 4-WIRE HOOKUP
SINGLE STAGE HEAT AND COOL
Y O G W B RH RC
Gas
Valve
or
Heater
FAN
A/C
Comp.
System
XFMR
RH-RC JUMPER
PROVIDED
COMMON
TYPICAL 2-TRANSFORMER 24-VAC 5-WIRE HOOKUP
SINGLE STAGE HEAT AND COOL
Y O G W B RH RC
Gas
Valve
or
Heater
FAN
A/C
Comp.
Heat
XFMR
Cool
XFMR
RH-RC JUMPER
REMOVED
COMMON 2
COMMON 1
TYPICAL SINGLE-STAGE HEAT PUMP HOOKUP
Y O G W B RH RC
FAN
Heat Pump
Compressor
System
XFMR
Reversing
Valve
RH-RC JUMPER
PROVIDED
USE
B or O
NOT BOTH
SYSTEM
COMMON
WIRING DIAGRAM NOTES
(APPLIES TO ALL DRAWINGS)
• The DASHED lines are optional depending upon
your system type.
• Verify whether “C”, “X” or “B” wires are connected
to system common.
• If “B” and “O” are both present, it is likely that “B”
is a system common.
• If a “B” wire in your system is a common, then
connecting it to the “B” terminal may cause damage to
your system.
• If “Y” and “C” are both present, it is likely that “C”
is a system common.
52002
© COPYRIGHT 2006 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED