Linear CCM-2 Home Security System User Manual


  Open as PDF
of 1
 
Copyright © 2005 Linear LLC 225975 A
CCM-2
Color
Camera
Module
Installation Instructions
PRODUCT DESCRIPTION
Linear’s Model CCM-2 (P/N ACP00936) CCTV camera can be installed inside the
RE-2 Residential Telephone Entry System. The camera provides a video signal for
viewing the area in front of the entry system.
The camera is continuously powered by the RE-2. The camera focus has been factory
adjusted to a range of three to four feet.
The CAMERA connector is used to connect the camera to the RE-2. The 4-conductor
cable routes power to, and video from the camera.
The VIDEO OUT connector is the camera output for connection to a video cable with
a Type “BNC” connector. Up to 400 feet of 75-ohm RG-59 video cable can be used.
Longer cable runs may require the use of a video amplifier.
NOTE: If camera is being installed on an existing installation, system power
should be off prior to installing the camera.
1. REMOVE THE COVER PLATE
2. PREPARE TO MOUNT THE CAMERA 3. REMOVE THE LENS CAP 4. INSTALL THE CAMERA
5. CONNECT THE CAMERA AND VIDEO CABLE 6. TEST CAMERA LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship
for twenty four (24) months. The Warranty Expiration Date is labeled on the
product. This warranty extends only to wholesale customers who buy direct from
Linear or through Linear’s normal distribution channels. Linear does not warrant
this product to consumers. Consumers should inquire from their selling dealer
as to the nature of the dealer’s warranty, if any. There are no obligations or
liabilities on the part of Linear LLC for consequential damages arising
out of or in connection with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or profit, or
cost of removal, installation, or reinstallation. All implied warranties, including
implied warranties for merchantability and implied warranties for fitness, are valid
only until Warranty Expiration Date as labeled on the product. This Linear LLC
Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an
RPA# and other important details.
(760) 438-7000
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
REMOVE THE FOUR
SECURITY SCREWS
TO OPEN THE CASE
REMOVE THE SIX CIRCUIT
BOARD RETAINING SCREWS
AND FLIP THE CIRCUIT BOARD UP
REMOVE THE TWO RETAINING
SCREWS AND BRACKET
S
REMOVE THE
BLACK DO
T
ON CAMER
A
GASKET
CAMERA
MOUNTING
AREA
REMOVE THE LENS CAP
FROM THE CAMERA LENS
CONNECT THE VIDEO CABLE FROM
THE MONITOR OR MODULATOR TO
THE RE-2'S VIDEO OUTPUT CONNECTOR
CONNECT THE CAMERA'S
CABLE TO THE RE-2'S
CAMERA CONNECTOR
CAMERA
CONNECTO
R
VIDE
O
OUTPUT
CONNECTO
R
APPLY POWER TO THE ACCESS SYSTEM
THEN VIEW THE VIDEO MONITOR TO TEST
THE VIDEO OUTPUT FROM THE CAMERA
SMALL ADJUSTMENTS FOR TILT
CAN BE MADE BY ADJUSTIN
G
THE CAMERA'S BRACKET
MOUNT THE CAMERA
WITH THE BRACKE
T
HOLE ON THIS SIDE
SECURE THE CAMERA
WITH THE TWO RETAINING
BRACKETS AND SCREWS
PLASTI
C
CAMERA
GASKET
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,CCM-2 - LINEAR P/N: 225975 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1