Lightolier ISF:302 Indoor Furnishings User Manual


  Open as PDF
of 1
 
INSTALLATION INSTRUCTIONS 12V LOW VOLTAGE
AND 120V MOUNTING FRAME
INSTRUCTION SHEET
12-01/Rev-04
ISF:302
FIG.1 FIG.2
FIG.3 FIG.4
MOUNTING
FRAME
MOUNTING
BAR
MOUNTING
BAR
BUILT-IN
NAILER
WOOD
JOIST
MOUNTING
BAR
MOUNTING
FRAME
"PRY-OUT"
PLUG
FLEXIBLE
WIRE
WIRE
CLAMP
JUNCTION
BOX
FIG.11
ANCHOR
CLIP
MOUNTING BAR
EXPANDABLE
T-BAR
FRAME
A. MOUNTING BAR: For new ceilings
Note-1: The mounting bars are extensible from 12-1/2 to 27-1/4
max. for 302MR, 302ES model and 29 for 402MR model.
Note-2: For off-centre installation, use the 20 expandable
mounting bars (Nº1964, order separately).
1. Insert the mounting bars into the proper openings on the short
side or the long side of the mounting frame. (Fig.2)
2. Align the mounting bar with the bottom edge of the wood joist.
(Fig.1)
3. Push in the built-in nailer. (Fig.1)
B. MOUNTING BAR: For a T-Bar ceilings
1. Position the notch in the mounting bar on top of the
T-bar frame. (Fig.10)
2. Fasten with the metal wire or other. (Fig.10)
Note: When used with the 20 expandable mounting bars
(Nº1964), use the anchor clip for T-bar frame (Nº1956, order
separately). (Fig.11)
C. MOUNTING FRAME:
1. Install the locking clip. (Fig.3)
Note-1: The locking clip is also available separately
(Nº0098, order separately).
Note-2: To lock more securely into place fold the locking tabs.
(Fig.2)
D. WIRE-IN:
1. Remove the appropriate "Pry-out plug".
2. Insert the supply lead into the junction box:
a) If using FLEXIBLE CONDUIT: Use a BX connector (not provided).
b) If using FLEXIBLE WIRE: Insert under the wire clamp. (Fig.4)
3. Connect the ground lead. (Fig.5,6,7)
4. Connect the white leads (NEUTRAL) together, and the black leads
(120V) together. (Fig.5,6,7)
E. CEILING:
1. Cut a hole in the ceiling (3-3/4 for Model 302 or 4-3/4 for
Model 402), using the mounting frame as template (if applicable).
(Fig.8)
2. Use the screws to adjust the housing height. Note: Ensure
that the housing is level with the ceiling. (Fig.9)
3. Tighten the screws when completed. (Fig.9)
CAUTION: The socket must not be used for temporary
lighting, a protective glass is required for the lamp.
TRIM:
Install the trim using the appropriate sheet.
NOTE: WARNING RISK OF FIRE
Transformer contains fixture thermal protector. Use only replacement
transformer obtained from LIGHTOLIER.
MOUNTING
BAR
FIG.10
NOTCH
T-BAR
FRAME
LOCKING
TAB
LOCKING
CLIP
METAL
WIRE
JUNCTION
BOX
INPUT (120V)
NEUTRAL (white)
GROUND
LAMP
LOW VOLTAGE
TRANSFORMER
WHITE
BLACK
THERMAL
PROTECTOR
JUNCTION
BOX
THERMAL
PROTECTOR
LAMP
INPUT (120V)
GROUND
NEUTRAL (white)
BLACK
NEUTRAL
WHITE
WHITE
BLUE
FIG.8 FIG.9
HOUSING
302MR - 402MR
302ES
FIG.5
(302MR)
FIG.6
(302ES)
JUNCTION BOX
LAMP
LOW VOLTAGE
TRANSFORMER
THERMAL
PROTECTOR
NEUTRAL (white)
GROUND
BLUE
BLACK
BLACK
INPUT (120V)
NEUTRAL (white)
FIG.7
(402MR)
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with National Electrical Code or Canadian Electrical
Code (as applicable) and local regulations. To ensure full compliance with local codes and regulations, check with your local
electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
SCREWS