Filter
Top Products
E2010 CCN 15214158
(800) D)$;
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
1” DIAPHRAGM PUMP
OPERATOR’S MANUAL
PE10P-X-X-A0S
RELEASED: 9-14-04
REVISED:
(REV.
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637396-XX forfluidsection repair(see page 4).NOTE: This kitalso con-
tains several air motor seals which will need to be replaced.
637412 for air section repair (see page 6).
PUMP DATA
Models see Model Description Chart for “-XXX”...........
Pump Type Non-Metallic Air Operated Double Diaphragm.......
Material see Model Description Chart...........
Weight PE10P-AK
S-XXX-A0S 25.40 lbs (11.52 kgs)... ...
PE10P-AP
S-XXX-A0S 18.92 lbs (8.58 kgs)...
PE10P-BK
S-XXX-A0S 25.40 lbs (11.52 kgs)...
PE10P-BP
S-XXX-A0S 18.92 lbs (8.58 kgs)...
PE10P-FK
S-XXX-A0S 26.72 lbs (12.12 kgs)...
PE10P-FP
S-XXX-A0S 19.44 lbs (8.82 kgs)...
PE10P-YK
S-XXX-A0S 26.29 lbs (11.93 kgs)...
PE10P-YP
S-XXX-A0S 19.16 lbs (8.69 kgs)...
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar).........
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar).....
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar)..........
Maximum Flow Rate
(flooded inlet) 53.0 g.p.m. (200.6 l.p.m.)....
Displacement / Cycle @ 100 p.s.i.g. 0.226 gal. (0.86 lit.)...
Maximum Particle Size 1/8” dia. (3.2 mm)............
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM -60_ to 280_ F(-51_ to 138_ C)...........
Hytrel
R -20_ to 150_ F(-29_ to 66_ C)................
Nitrile 10_ to 180_ F(-12_ to 82_ C).................
Polypropylene 35_ to 175_ F(2_ to 79_C)...........
PVDF (Kynar
R)10_ to 200_ F(-12_ to 93_ C)..........
Santoprene
R -40_ to 225_ F(-40_ to 107_ C)...........
PTFE 40_ to 225_ F(4_ to 107_ C).................
Viton
R -40_ to 350_ F(-40_ to 177_ C)................
Dimensional Data see page 8................
Mounting Dimension 5.032” x 10.050” (127.8 mm x 255.3 mm)...
Noise Level @ 70 p.s.i., 60 c.p.m. 79.7 db(A)
{.....
Thepump soundpressure levels publishedhere have beenupdated toan Equivalent
Continuous Sound Level(L
Aeq
) to meetthe intent of ANSIS1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
PE10P-AXS-XXX-A0S
PE10P-BXS-XXX-A0S
PE10P-YXS-XXX-A0S
PE10P-FXS-XXX-A0S
Figure 1
MODEL DESCRIPTION CHART
PE10 P -X X S -X X X -A0S
PE10P - XXS - X X X -A0S
637396 - X X
DiaphragmBall
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: MODEL # PE10P-FPS-PAA-A0S
FLUID SECTION SERVICE KIT # 637396-AA
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene M - Medical Grade Santoprene
C - Hytrel T - PTFE / Santoprene
G - Nitrile V - Viton
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Fluid Connection / Location
A - 1 - - 11-1/2 N.P.T.F. - 1
B-Rp1-11BS
F - 1” A.N.S.I. / D IN Flange / End
Y - 1” A.N.S.I. / DIN Flange / Center
Center Section Material
P - Polypropylene
Ball Material
A - Santoprene T - PTFE
C - Hytrel V - Viton
G - Nitrile
www.ingersollrandproducts.com
11-15-10
08)