IDEAL INDUSTRIES MX34 Garage Door Opener User Manual


 
RESIDENTIAL
R E S I D E N T I A L
RESIDENTIAL
GARAGE DOORS
RESIDENTIAL
GARAGE DOORS
Tape Measure
Level
Pliers
Step Ladder
Screwdriver
Saw
Claw Hammer
Sawhorses
7
/
16
",
1
/
2
" &
9
/
16
" Sockets and Ratchet
Drill with
3
/
16
",
5
/
32
",
3
/
8
" &
7
/
16
" drill bits
Two short pieces of rope about 4' in length
Locking Pliers or C Clamps
Tw o
1
/
2
" x18" Winding Bars (Torsion Springs only)
3
/
8
" Open-end Wrench (Torsion Spring Only)
NOTE: On 8' and 9' wide doors, a reinforcement strut must be
purchased if an automatic garage door opener is installed.
The majority of homes today have automatic garage door openers.
Therefore, Ideal doors do not include a lock. If desired, an easy-to-install,
heavy-duty, keyed lock is available.
TOOLS NEEDED...
All tools may be purchased in Hardware Dept.
All steel used in this
product is 100% recyclable
at the end of its useful life.
REID-CH-RESIBR-08
In the interest of better quality and value,we are continually improving
and updating our products. Consequently, photos, illustrations and
available options may sometimes differ from present models.
Ideal Door
1-800-621-3667
Ideal Door is a brand of Clopay Building Products.
Clopay Building Products Company, Inc. 2008
A Griffon Company, Inc. Printed in U.S.A.
®
©
®
11"
14
1
/2"
6
1
/2"
n/a
12"
15
1
/2"
10"
7"
12"
14"
9
1
/2"
n/a
3
3
/4"
3
3
/4"
6"
6"
ITEMS NEEDED BEFORE INSTALLING YOUR GARAGE DOOR
Headroom/Sideroom Requirements
EXTENSION
SPRING
TORSION
SPRING
SIDEROOM
EZ-SET®
TORSION SPRING
12" TRACK RADIUS
15" TRACK RADIUS
LOW HEADROOM
DOUBLE TRACK (standard)
LOW HEADROOM DOUBLE
TRACK (rear mount)
FLOOR
CEILING
4. BACKROOM
3. HEADROOM
2.
LEFT
SIDE
2.
RIGHT
SIDE
WIDTH
HEIGHT
MEASURING FOR YOUR DOOR
1. Measure existing door width and height in feet and inches.
This determines the size of door needed. The rough opening
should be the same size as the door.
Width: ____________________ Height: ____________________
2. Measure for sideroom: 3
3
/
4
" is required on each side for
installation of the vertical track for standard extension or torsion
springs, or EZ-SET Torsion Spring.
Sideroom: __________________
3. Measure area labeled “headroom”—distance between the top of
the door opening (“jamb header”) and the ceiling (or first
obstruction, ex: light fixture). 11" is required for standard
installation of extension springs; 12" on standard torsion springs
and EZ-SET Torsion Spring. If you have restricted headroom,
special hardware is available. Low headroom hardware is available
to reduce requirement to as low as 4
1
/
2
" (minimum with standard
extension spring). EZ-SET Torsion Spring low headroom
requirement is 9
1
/
2
". Note: If door height extends above the
opening, the headroom measurement should be adjusted accordingly.
Existing headroom: ___________
Headroom needed: ___________
4. Measure area labeled “backroom”—distance is measured from the
garage door opening toward the back wall of the garage.
Backroom: __________________
Common garage door widths include 8', 9', 16' and 18'. Common garage door
heights include 7' and 8'. See Menards Team Member for additional size availability.
®
®
®
Complete Garage
Door Selection
Steel Panel Doors Carriage House Doors