Filter
Top Products
(Model EP 377 and 374 only)
( Model 373/372 )
2.Lower the foot and sew slowly u
ntil the d
esire
d length is sewn
,
the
n stop the machine at
1. Set the patter
n selec
tor at
. Then pass the needle threa
d
through
the ope
ning in the butto
nhole foot and draw bo
th need
le
an
d bobb
in threa
ds to the left side. Turn the ba
lance w
heel
tow
ards you until th
e need
le come
s to the poi
nt
3. Rais
e the nee
dle and s
et the se
lecto
r at . Th
en sew
several stitches of bar tac
k until the n
eedle i
s at point
5. Rais
e need
le and se
t the sele
ctor at then s
ew sev
eral
stitche
s of final ba
r tack. Stop the machine with the needle at
point . To lock thr
eads
, set the pattern selecto
r at B (z
ero
po
int of zigz
ag widt
h). And sew a few st
itche
s.
4. Rais
e the needle and set the selector at
then sewt
he
rig
ht side o
f butto
nhol
e the sam
e lengt
h as the left side of
bu
ttonhole. Stop t
he machine at
6. Cut the
buttonhole open carefully u
sing a seam ripper, taking ca
re
no
t to damage the bar tacks.
1. Set th
e patter
n selector at Th
en pass th
e needle threa
d
through the open
ing in the b
uttonhole fo
ot and dr
aw both of
ne
edle and bobbin threa
ds to the right side. Tu
rn the ba
lance
wheel tow
ards yo
u until the n
eedle c
omes to t
he poin
t
2. Lower the foot and sew slow
ly until a desired le
ngth is se
wn,
th
en stop th
e machine at
3. Rais
e the nee
dle and s
et the selector a
t
then sew
se
veral s
titches of bar tack u
ntil the n
eedle is at point
4. Rais
e the nee
dle and set the sel
ector at
then s
ew the
left sid
e of but
tonhole just a
s the sa
me len
gth as th
e right side of
butto
nhole
. Stop the m
achin
e at
5. Raise the nee
dle and set the sel
ector a
t
then se
w seve
ral
stitch
es of fin
al bar ta
ck. Stop the m
achine with th
e needle at
poi
nt
6. Cu
t the bu
ttonhole op
en ca
refull
y using a seam
ripper, taking
care not to da
mage the ba
r tacks.
Note
: To make a
heavier buttonhole, sew
twice b
y repe
ating the
same p
roced
ure.
(2).
(3).
(4).
(5).
(1).
(1).
(2).
(3).
(4).
(5).
SEWING BUTTONHOLES (Model 377 and 374)
¡°¡±
¡°¡±
¡°¡±
¡°¡±
¡°
SEWING BUTTONHOLES (Model 373/372)
SEWING ZIPPERS
Model 377
Model 373/372
Model 374
zipper foot
Pattern selector
Presser foot
Stitch length dial
1 to 4
M( )
1-3( )
1 to 4
A( )
Raise the foot and the needle to its highest position by turning
the balance wheel towards you. Replace the foot with the zipper
foot.
1. Pin or baste the zipper tape to the fabric and place the work-
piece in position under the foot.
Attach snap on zipper foot so that the needle passes on its
left hand side.
* When starting sewing, both needle and bobbin threads ends
should be put away under the foot.
2. Sew on the right side of the zipper by guiding Zipper teeth
as close as possible to the needle drop. Before the foot reaches
the slider on the zipper tape, raise the foot and open the
zipper by keeping the needle in the fabric.
Lower the foot and sew on the remaining of the seam,
3. To sew the left side zipper change position of foot to bring
the foot to the left side of the needle. Sew on in the same
way as you did on the right side of zipper.
Zipper foot
Elements
tape
Fabric
Elements
Slider
Fia. 1
Slider
Element
Zipper foot
Needle
Fabric
Tape
Element
15
English
zipper foot zipper foot
¡°¡±
¡°¡±
¡°¡±
¡°¡±