Filter
Top Products
by
Scissor Lift –SLX Series
Motorized Ceiling-Recessed
Video Projector Lift
DIMENSIONS & DATA MODEL SLX11 MODEL SLX12 MODEL SLX13 MODEL SLX14 MODEL SLX15 MODEL SLX16 MODEL SLX17
Height of lift in closed position* 13¾" 15¾" 15¾" 17
1
/
8
" 17
1
/
8
" 19
1
/
8
" 19
1
/
8
"
Overall lift dimensions (W
XL**) 27" x 29½" 27" x 29½" 27" x 29½" 27" x 29½" 27" x 29½" 27" x 29½" 27" x 29½"
Max. down travel (Service Position) 11' 12' 13' 14' 15' 16' 17'
Approx. travel time to serv. position 99 sec. 108 sec. 117 sec. 125 sec. 134 sec. 143 sec. 152 sec.
Capacity (lbs.) 350 350 350 350 350 350 350
Net weight (lbs.) 160 165 170 175 180 185 190
Shipping weight (lbs.) 186 191 196 201 206 211 216
Amperes*** 2.6 2.6 2.6 2.6 2.6 2.6 2.6
Show Position — Set at factory. Can specify at time of order
Max. projector height — If recessed, limited only by amount of available space above the ceiling
Min. clear space above fi nished ceiling—Will vary according to projector height, optional mounting bracket, optional ceiling closure, optional plenum housing
Size E Size J Size G Size U
Max. Projector Size W x L 25½" x 35½" 25½" x 39½" 31½" x 44½" 27½" x 30½"
Ceiling Opening W x L 29½" x 40" 29½" x 44" 35
7
/
8
" x 49" 36
7
/
8
" x 36
7
/
8
" (Trim edge–to–edge)
Ceiling Closure Panel W x L 30" x 40
5
/
8
" 30" x 44½" 36
3
/
8
" x 49½" 37
3
/
8
" x 37
3
/
8
" (Trim edge–to–edge)
Optional ceiling mounting bracket — SMS Low Profi le for projector lifts.
Optional plenum housing — Height, width and length will vary according to choice of projector
* Only height of Scissor Lift in closed position. Overall height of projector, plus optional mounting bracket, plus optional ceiling closure, plus optional plenum
housing adds to overall height of equipment installed above ceiling. SMS Low Profi le Bracket adds 4
7
/
8
" to height, including universal projector bracket.
** Length includes the ½" cable carrier of the Cable Management System.
*** Does not include any load placed on Scissor Lift’s prewired power cable.
Please Check All Appropriate Selections
Select Model:
Model SLX11 Model SLX14 Model SLX17
Model SLX12 Model SLX15
Model SLX13 Model SLX16
Select Controls: This unit comes standard with one 12v
Toggle Switch and 12v Momentary Key Control. For other
switching options, please select from below:
Optional Video Interface Control(VIC12) for projection screen operation
Optional Key Operated Power Supply Key Switch (On-off)
Optional LVC-III — 24v (low voltage)*
*This is required for any of the following options:
Wireless Remote Control (radio frequency transmitter & receiver)
Wireless Remote Control (infrared transmitter & receiver)
Select Optional Accessories:
Optional factory installed cables for RGBHV, Video, and RS232
Specify connector types:
Optional ceiling closure
E J
G U
Optional ceiling fi nish kit
Optional 2' x 2' ceiling access door to allow access above fi nished ceilings
White painted fi nish
Accepts ceiling tile
(Please Note: option ceiling access door is highly recommended.)
Optional plenum housing
Optional SMS Low Profi le Projector Bracket (Max. load 26 lbs.)
If you are ordering an SMS Low Profi le Projector Bracket with this
unit, please specify projector manufacturer and model number:
(If not available at time of order, it may be provided later)
Copyright © 2007 Draper Inc. Form ScissorLift-SLX_Sub07-R Printed in U.S.A.
U.S. Patent D395,909
PROJECT:
ARCHITECT:
CONTRACTOR:
SUPPLIER:
DATE: REVISED:
Specifi cations—Scissor Lift
video projector lifts, Model (SLX11-17), for projectors weighing up to
350#. Dove grey baked powdercoat fi nish. Projector bolts onto operating pan, or
mount to pan with optional SMS Low Profi le Lift Bracket. Electrically op er at ed
110-120V AC, 60 Hz. UL rec og nized gearmotor, with metal chain drive system,
to be lifetime lubricated. Draws 2.6 amps. Projector to be sus pend ed from 3
1
/
4
"
x 24" x 26" x 11 ga. steel pan supported by steel scissor arms and operated by
two,
3
/
16
" aircraft cables with 4200 foot/pounds tensile strength per cable. Scissor
Lift equipped with 3 sets of stabilizing scissors, positioned on the left, right, and
rear sides. Also equipped with fail-safe inertial safety belt system and Cable
Management System with projector power cord. Factory set limit switches to
automatically stop travel at store, show, and service positions. Single Station
Control, standard, consists of one 12V toggle switch to lower lift from “stored” to
“show ” positions, and one 12V momentary key switch to lower lift from “show” to
“service” position. Optional LVC-III for operation from “stored” to “show” positions
only; required for use with Key Operated Switch.
Optional plenum housing consists of suitable painted steel panels for use in return
air plenum situations. Optional ceiling closure panel, fi nished in white baked
textured powdercoat, shall descend smoothly with projector. Choose a model
based on number of feet needed (11'-17') to put projector within easy reach for
servicing.
Please Note: The Scissor Lift should be specifi ed in conjunction with a DRAPER
motorized screen.
SMS Low Profi le Fixed Mount: Ceiling mount shall consist of a steel ball joint and
Universal Projector Bracket. Mount shall be 2" long, and shall securely attach to
lift with steel mounting plate (provided). Installer shall provide mounting hardware
appropriate to ceiling conditions. Steel ball joint attaches to Universal Projector
Bracket with twist-lock engagement. Min. overall height of assembled unit shall
be 4
7
/
8
". Mount shall provide up to 30° roll or pitch adjustment and 360° yaw
adjustment at ball joint. Two setscrews lock ball joint in position. Max. load 26 lbs.
Ceiling Access Door: Provides access to projector and lift when unit is installed
above hard ceiling. Finished by ceiling contractor to match ceiling.