Filter
Top Products
The Science of Security
™
Compatible with the
following systems:
CCoonncceepptt 445500 ((GG55))
SSoollaarriiss ((GG44))
MMiilllleenniiaa ((GG44))
OOmmnniiSSttaarrtt GG44))
AAvvaannttgguuaarrdd44 ((GG44))
IInntteelllliiGGuuaarrdd 99000000 ((GG44))
IInntteelllliiGGuuaarrdd 88000000 ((GG44))
IInntteelllliiGGuuaarrdd 77000000 ((GG44))
IInntteelllliiGGuuaarrdd 66000000 ((GG44))
CCyybbeerr44 ((GG44))
CCoonncceepptt 660000 ((GG44))
CCoonncceepptt 440000 ((GG44))
CCoonncceepptt 220000 ((GG44))
AAccee 77550000 ((GG44))
AAccee 44000000 ((GG44))
CCoonncceepptt 110000 ((GG44))
MMaattrriixx 22
MMaattrriixx 33
MMaattrriixx RRSS22
MMaattrriixx RRSS33
44 BBuuttttoonn,, CCaarrbboonn FFiibbeerr AACCGG rreeppllaacceemmeenntt TTrraannssmmiitttteerr
PN 904100
MADE IN TAIWAN
©2002 Directed Electronics, Inc. Vista CA 92083
All rights reserved.
P/N 904100 11/02
1. IGNITION ON: Place the key into the ignition and
turn to the ON position or start the engine.
2. ENTER PIN NUMBER: Enter your PIN number
using the Plainview 2 valet switch.
Note: The Factory default PIN number is 2 and can
be entered by pressing the
*
button twice then the
"blank" button once of the Plainview 2 valet switch.
3. PRESS/HOLD/RELEASE: Immediately PRESS
and HOLD the
*
button until you hear one chirp
and the Status LED turns on, then RELEASE the
*
button.
4. PRESS/RELEASE: PRESS and RELEASE the
"blank" button once. Pause until you hear one
chirp.
5. PRESS/RELEASE: PRESS and RELEASE the
*
button once.The siren will chirp once as you
push the button.
6. TRANSMIT: Press the button on you new
transmitter.The siren will chirp once to confirm it
has received the transmission.
7. TRANSMIT AGAIN: Press the button a
second time.The siren will chirp twice to confirm
it has learned your new transmitter.
8. IGNITION OFF: Turn the ignition off and remove
the key: The alarm will chirp three times to
indicate exiting transmitter learn routine.
9. TEST TRANSMITTER: Press the button
to verify that the transmitter is operating the
alarm system.
Note:This transmitter auto-learn routine is applicable
to specific system/ transmitter combinations, use
the following reference guide or consult your local
Clifford dealer for your particular application
904065 transmitter: Arrow 5 /Arrow 3 / Cyber 2
904100 transmitter: Concept 100 / Concept 450/
Intelliguard 6000 / Cyber 4
904075 transmitter: All other systems
This device complies with Part 15 of FCC rules.
Operation is subject to the following conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation. Changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this device.
44 BBuuttttoonn,, CCaarrbboonn FFiibbeerr AACCGG rreeppllaacceemmeenntt TTrraannssmmiitttteerr
PN 904100
To program your new transmitter:
TM