Filter
Top Products
Model(s) : DXUFSR2 Fan Heater
Installation and Operating Instructions
Dimensions
(millimetres)
08/35169/0 Issue 0
Using the Heater
Thermostat Control - see Fig. 3
The heat output is controlled by the
thermostat, according to the room
temperature.
Turn the thermostat knob fully clockwise
to maximum setting initially. When the
room is warm enough, reduce the setting
slowly until the heater just clicks off.
The heater will now cycle on and off to maintain your selected room
temperature. An audible click may be heard when the thermostat
operates - this is normal.
Note : If the heater does not come on when the thermostat is at a low
setting, this is normally because the room is warmer than the thermostat
setting and is not a fault.
* When the heat control is set to ‘ ‘ for cool blow, set the thermostat
control to maximum.
Position ‘ ‘ will turn the heater on and off to maintain a temperature of
approximately 5°C.
- OFF
- Cool Blow*
- Half heat
- Full heat
Heat Control - see Fig. 2
(IP21)
H W D
265 230 230
Model(s) Specification
DXUFSR2 2.0kW Thermostat & Switch
Fig. 2
Fig. 3
(see Fig. 3)
Fig. 1
(see Fig. 2)
IMPORTANT SAFETY ADVICE
DO NOT use the heater on deep pile carpets or the long hair
type of rugs, or less than 750mm (30") away from any
overhanging surface. Keep combustible materials such as
drapes and other furnishings clear from the front, sides
and rear of the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate surroundings of a
bath, a shower or a swimming pool.
DO NOT place the heater directly below a fixed socket outlet.
The socket-outlet must be accessible at all times to enable
the mains plug to be disconnected as quickly as possible.
DO NOT COVER or obstruct the air inlet and outlet openings
in any way.
The heater must be on a flat stable surface when in use.
DO NOT operate the heater with the mains lead overhanging
the front outlet grille.
The appliance is designed to self-right itself if it is
accidentally knocked over, however the appliance should
not be maltreated to perform this function.
ALWAYS ENSURE THE APPLIANCE DOES NOT COME TO REST
ON THE MAINS LEAD OR ALLOW THE LEAD TO BECOME
WRAPPED AROUND THE APPLIANCE - THIS MAY IMPAIR THE
SELF-RIGHT FUNCTION.
NEVER leave the heater unattended when it is used by or
near the aged, infirm person’s or children.
THE HEATER CARRIES THE WARNING SYMBOL INDICATING
THAT IT MUST NOT BE COVERED.
The instruction leaflet belongs to the appliance and must
be kept in a safe place. If changing owners, the leaflet must
be surrendered to the new owner.
IMPORTANT – If the mains lead of this appliance is damaged,
it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard.
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
Electrical connection
This heater must be used on an A.C.~ supply only and the voltage
marked on the heater must correspond to the supply voltage. This
heater is fitted with a plug incorporating a 13 amp fuse. When replacing
the fuse, a 13 amp fuse approved by ASTA to BS 1362 must be used.
If the plug is not suitable for the socket outlets in your home, the plug
must be cut off and an appropriate one fitted. A plug cut off from a
mains lead will give a shock hazard if inserted into a 13 amp socket
elsewhere in the house. To avoid this, it should be disposed of
immediately.
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
NOTE: The fuse cover of a non-rewirable plug must be refitted when
changing the fuse. Should the cover become lost, the plug must not be
used until the correct replacement fuse cover is obtained from your
supplier or by contacting our customer helpline.
IMPORTANT : The wires in this mains lead are coloured in accordance
with the following code :
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead may not correspond with
the coloured markings in your plug, proceed as follows :
Connect the BROWN wire to the terminal marked ‘L’ or coloured RED.
Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.
Note : ‘L’ or ‘N’ must not be connected to the EARTH terminal marked
‘E’ or or coloured GREEN or GREEN AND YELLOW.
If in doubt, consult your electrician.