Filter
Top Products
4. Removing the Hand Shower from the Shower Head.
2. Install hand shower.
Parts Included
Shower Head
Hand Shower
3. Insert hand shower into shower head.
a.
The Hand Shower
should be inserted
at an angle so the
tab on the top of
the Hand Shower
fits into the slot in
the Shower Head.
b.
Gently push the
Hand Shower into
the Shower Head.
a.
Confirm the hose washers are installed in the hose
nuts at each end of the hose.
b.
Connect one end of the Flexible Hose to the Shower
Head. Connect the other end of the Flexible Hose to
the Hand Shower. All connections should be made
by hand tightening.
Hand
Shower
snaps into
place.
Insert Hand
Shower at an
Angle into the
Shower Head.
• If the Shower Head
moves when
removing the Hand
Shower, tighten the
connection between
the Shower Head
and the Shower Arm.
Flexible Hose
1. Install the shower head.
a.
The Hand Shower
should be removed
at an angle to
release from the
Shower Head.
b.
Once the Hand
Shower is released
from the lower clips
of the Shower Head,
gently pull the Hand
Shower away from
the slot in the upper
portion of the
Shower Head.
Pull the lower
part of the
Hand Shower
Handle away
from the
Shower Head.
Pull the Hand
Shower down,
away from
the slot in the
Shower Head.
Hose Washer
(2)
a.
a.
b.
b.
a.
Make sure to turn off water supply before installing
the Shower Head.
b.
Remove existing Shower Head from Shower Arm.
c.
Apply
Plumber
tape (not provided) to Shower Arm if
necessary, to ensure leak-free connection.
d.
Hand tighten the Ball Connector of the Shower Head to
the Shower Arm. (Use a wrench if necessary for firm
installation.)
In2ition
®
Installation Instructions
All parts and finishes of the Delta
®
faucet
be free from defects in material &
wor
mer
kmanship for as long as the original consu-
purchaser owns their home. Delta Faucet
Comp
any recommends using a professional
all installation & repair.
Delta
will replace, FREE OF CHARGE,
during
the warranty period, any part or finish that proves
defective in material and/or workmanship under
normal installation, use & service. Replacement
parts may be obtained by calling 1-800-345-DELTA
(in the U.S. and Canada) or by writing to:
In the United States:
In Canada:
Delta
Faucet Company
Masco Canada Limited, Plumbing Group
Product Service
350 South Edgeware Road,
55 E. 111th Street
ST. Thomas, Ontairo, Canada N5P 4L1
Indianapolis, IN 46280
are warranted to the original consumer pur-
to
chaser
plumber for
Limited Lifetime Warranty
Cleaning of Parts
Only clean with a mild non-
abrasive detergent and soft
cloth.
Note: Any other cleaning
product not specifically
designed for cleaning plastic
or metal surfaces may damage
the finish.
WARNING: Plumbing Codes require that shower heads and hand showers provide a small but continuous flow of water (trickle) when in “PAUSE” mode. Because of this continuous flow, in certain circumstances
pressure variations in the water line and/or changes in the position of shower temperature control handle while in “PAUSE” mode could result in dramatic changes to the temperature of the water when the shower
head or hand shower is returned to the “ON” position.
ALWAYS point the shower head away from yourself when returning to the “ON” position and feel the water with your hand before resuming your shower to ensure the water flow is not too hot or too cold. DO NOT
allow children or others who might not understand this warning to use the “PAUSE” function.
67503 Rev. A
This warranty is extensive in that it covers replac-
of all defective parts and even finish,but
these are the only twothings that are covered.
LABOR CHARGES AND/OR DAMAGE INCURRED
IN INSTALLATION,REPAIR, OR REPLACEMENT AS
WELL AS ANY OTHER KIND OF LOSS OR
DAMAG-
ARE EXCLUDED.Proof of purchase(original sales
from the original consumer
purchaser
must
be made
available
to
Delta
for
all warranty claims.
THIS
IS THE EXCLUSIVE WARRANTY
BY DELTA
FAUCET COMPANY, WHICH DOES NOT
MAKE
ANY OTHER WARRANTYOFANY KIND,INCLUDING
THE IMPLIED WARRANTY
OF MERCHANTABILITY.
ement
ES
receipt)
© 2011 Masco Corporation of Indiana
www.deltafaucet.com