Filter
Top Products
IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE TAKEN,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS
BEFORE USING APPLIANCE.
KEEP AWAY FROM WATER
DANGER –TO REDUCE THE RISK
OF ELECTRIC SHOCK: ALWAYS UNPLUG THIS
APPLIANCE FROM THE ELECTRICAL OUTLET
BEFORE CLEANING.
WARNING–TO REDUCE THE RISK
OF BURNS, ELECTROCUTION, FIRE, OR INjURY TO
PERSONS:
1. Unplug from outlet before putting on or taking
off parts.
2. This mirror should not be used by or near children
or individuals with certain disabilities.
3. Use this mirror only for its intended use as
described in these instructions. Do not use
attachments not recommended by the manufacturer.
4. Never operate this mirror if it has a damaged cord
or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return
the mirror to a service center for examination and
repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert an object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are
being used or where oxygen is being administered.
9. To disconnect, be sure mirror is in the off position,
then remove plug from outlet.
10. Do not leave appliance unattended when it is
plugged in.
11. Be sure mirror is not in a position where it can
reflect sunlight; reflected sunlight can cause fire.
12. Do not use on a soft surface such as a bed, where
openings may be blocked.
13. Touch knob on mirror base until light shuts off.
Allow unit to cool and unplug cord before replacing
light bulbs.
14. Do not place or store appliance where it can fall
or be pulled into a tub or sink.
15. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
16. To protect against electrical hazards, do not use
while bathing or in the shower.
17. Never use while sleeping.
18. Do not use a bulb greater than 13 watts.
Use on any 120 volt 60 hertz AC electric outlet
(ordinary house current). Do not use it on any other
electrical outlet.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this mirror has a
polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
does not fit contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
CAUTION: BE SURE DIRECT SUNLIGHT DOES
NOT STRIKE MIRROR WHEN LEFT UNATTENDED;
REFLECTED SUNLIGHT CAN CAUSE FIRE.
1. Your lighted makeup mirror will rotate 350° so that
you can use either the normal, flat mirror or the 8x
magnifying mirror located on the opposite side.
2. Plug into any standard 120
volt wall outlet. The mirror light
is activated by touch. Touch the
base to turn light on or off.
3. After use, always touch the
knob on the base to turn the
mirror to the OFF position
and unplug.
4. The beauty and design of this mirror complement
any decor. Therefore, you may wish to leave the
mirror displayed. However, if you choose to store
the mirror, see section about storage for detailed
information.
Special Feature
This lighted makeup mirror uses a fluorescent
bulb. The bulb lasts up to 10,000 hours and does
not require replacement. In the unlikely event
that the bulb does need replacement, follow the
instructions below.
REPLACING FLUORESCENT TUBE LAMP
CAUTION: Turn off power and unplug mirror. Allow
to cool at least three minutes before replacing
fluorescent tube lamp. Replace tube lamp only
with tube lamp of same wattage rating. Remove
tube lamp with care to avoid breakage.
REPLACING FLUORESCENT TUBE LAMP
1. This mirror uses a 13W
maximum 120V type plug-in
fluorescent tube lamp.
2. Remove screws from left and
right sides of mirror. (See Fig. 1.)
3. Carefully lift off the removable housing from the
half that is affixed to the stand.
4. A cable tie is used to
protect the fluorescent tube
lamp during transportation. To
replace the fluorescent tube
lamp, you must first cut the
cable tie. While holding the
socket, pull the fluorescent
tube lamp out of the socket
with care to avoid breakage.
(See Fig. 2.) Align the metal
pins on the fluorescent tube
lamp with the holes in the
socket and push gently to
secure. (See Fig. 3.) After
the fluorescent tube lamp is
replaced, there is no need to
replace the cable tie.
5. Carefully replace the removable half after locating
and aligning the screw holes to the fixed half.
6. Insert screws into screw holes and tighten.
Fig. 1
Fig. 2
Fig. 3