Filter
Top Products
To Control the Opener Lights
In addition to operating the door, you may program the remote
to operate the lights.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
Model 953D 3-Button Security✚
®
Remote Control
OWNER’S MANUAL
For use with 315 MHz Security✚
®
garage door openers and
light controls that have a purple “learn” button. The code
between the remote control and the receiver changes with
each use, randomly accessing over a billion new codes.
NOTE: If using with a gate operator refer to gate operator
manual for programming instructions. Manuals are also
available on-line at chamberlain-diy.com.
The additional push buttons can also activate other 315 MHz
garage door openers and/or light controls. (Instructions for
programming light products are included with those
accessories.)
KG
1
3
9
7
5
KG
1
3
9
7
5
Instructions Are Described and Illustrated Below
1. Press and release the “learn” button on
the motor unit. The learn indicator light
will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks will
be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each
remote or keyless entry you wish to use.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
© 2007, Chamberlain Group Inc.
114A3104D All Rights Reserved
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
Replacement Parts
3V2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . .10A20
Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
Owner’s manual . . . . . . . . . . . . . . . . . . . . . . . . . . .114A3104
Owner’s manual - Spanish . . . . . . . . . . . . . . . . .114A3104SP
™
/
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NOOTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
The Remote Control Battery
The 3V2032 lithium battery
should produce power for up to
5 years. To replace battery, use
the visor clip or screwdriver blade
to pry open the case as shown.
Insert battery positive side up.
Dispose of old battery properly.
Replace the batteries with only
3V2032 coin cell batteries.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 212°F (100°C ) or
incinerate.
Battery
positive
side up (+)