BRK electronic SCO7 Smoke Alarm User Manual


  Open as PDF
of 1
 
5
M
odel SCO7
M
08-0048-010
Q 0
9/10 Printed in Mexico
I
MPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about
y
our Combination Carbon Monoxide & Smoke Alarm’s
o
peration. If you are installing this Alarm for use by
others, you must leave this manual—or a copy of it—
w
ith the end user.
© 2010 BRK Brands, Inc. All rights reserved. Distributed by BRK Brands, Inc.
3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: (800) 323-9005 • www.firstalert.com
I
NTRODUCTION
FIRE SAFETY TIPS
F
ollow safety rules and pre
vent hazardous situations: 1) Use smoking
m
aterials properly. Never smoke in bed. 2) Keep matches or lighters away from
c
hildren; 3) Store flammable materials in proper containers; 4) Keep electrical
a
ppliances in good condition and don’t
overload electrical circuits; 5) Keep
s
toves, barbecue grills, fireplaces and chimneys grease- and debris-free;
6
) Never leave anything cooking on the stove unattended; 7) Keep portable
heaters and open flames, like candles, away from flammable materials;
8
) Don’t let rubbish accumulate.
K
eep alarms clean, and test them weekly. Replace alarms immediately if they
a
re not working properly. Smoke Alarms that do not work cannot alert you to
a
fire. Keep at least one working fire extinguisher on every floor, and an
a
dditional one in the kitchen. Have fire escape ladders or other reliable means
o
f escape from an upper floor in case stairs are blocked.
BASIC SAFETY INFORMATION
•
Dangers, Warnings, and Cautions alert you to important operating
i
nstru
ctions or to potentially hazardous situations. Pay special
attention to these items.
•
This Smoke/CO Alarm is approved for use in single-family
r
e
sidences. It is NOT designed for marine or RV use.
•
This combination Smoke/Carbon Monoxide Alar
m
has two separate
a
larms. The CO Alarm is not designed to detect fire or any other
g
as. It will only indicate the presence of carbon monoxide gas at
the sensor
. Carbon monoxide gas may be pr
esent in other ar
e
as.
T
he Smoke Alarm
will only indicate the pre
sence of smoke that
r
eaches the sensor. The Smoke Alarm is not designed to sense
gas, heat or flames.
•
T
his Smoke/CO Alarm
cannot operate without working batteries.
Removing the batteries for any reason, or failing to replace the
b
atteries at the end of their service life, removes your protection.
•
NEVER ignore any alarm. See “If Your Smoke/CO Alarm Sounds”
f
or more information on how to respond to an alarm. Failure to
r
espond can r
esult in injur
y
or death.
•
The Silence Featur
es ar
e for your convenience only and will not
c
orrect a problem. See "Using the Silence Features" for details.
Always check your home for a potential pr
o
blem after any alarm
.
Failure to do so can result in injury or death.
•
Test this Smoke/CO Alarm once a week. If the Alarm ever fails to
t
est correctly, have it replaced immediately! If the Alarm is not
working pr
operly
, it cannot aler
t
you to a pro
blem.
•
This pr
oduct is intended for use in or
dinar
y indoor locations of
f
amily living units. It is not designed to measure CO levels in
compliance with Occupational Safety and Health Administration
(OSHA) commercial or industrial standards. Individuals with
m
edical conditions that may make them more
sensitive to carbon
monoxide may consider using warning devices which provide
audible and visual signals for carbon monoxide concentrations
u
nder 30 ppm. For additional information on carbon monoxide
and your medical condition contact your physician.
STEP BY STEP GUIDE TO PROGRAMMING
THIS ALARM
6 7 1 2 3
COMBINATION CARBON MONOXIDE & SMOKE ALARM
WITH VOICE & LOCATION AND
R
EMOTE CONTROL TEST/SILENCE
Printed in Mexico M08-0048-010 Q 09/10
First Alert
®
is a r
egister
ed trademark of the First Alert T
rust.
W
HAT YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
C
O is an invisible, odorless, tasteless gas produced when fossil fuels do not
burn completely, or are exposed to heat (usually fire). Electrical appliances
t
ypically do not produce CO.
T
hese fuels include:
W
ood, coal, charcoal, oil, natural gas, gasoline,
kerosene, and propane.
C
ommon appliances are often sources of CO. If they are not properly main-
tained, are improperly ventilated, or malfunction, CO levels can rise quickly.
CO is a real danger now that homes are more energy efficient. “Air-tight”
h
omes with added insulation, sealed windows, and other weatherproofing
can “trap” CO inside.
SYMPTOMS OF CO POISONING
These symptoms are related to CO POISONING and should be discussed
w
ith ALL household members.
Mild Exposure: Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).
Medium Exposure: Throbbing headache, drowsiness, confusion, fast heart rate.
E
xtreme Exposure:
C
onvulsions, unconsciousness, heart and lung failure.
Exposure to Carbon Monoxide can cause brain damage, death.
This CO Alarm measures exposure to CO over time. It alarms if CO levels
a
re extremely high in a short period of time, or if CO levels reach a certain
minimum over a long period of time. The CO Alarm generally sounds an
alarm before the onset of symptoms in average, healthy adults. Why is this
i
mportant? Because you need to be warned of a potential CO problem while
you can still react in time. In many reported cases of CO exposure, victims may
be aware that they are not feeling well, but become disoriented and can no
l
onger react well enough to exit the building or get help. Also, young children
and pets may be the first affected. The average healthy adult might not feel
any symptoms when the CO Alarm sounds. However, people with cardiac
o
r respiratory problems, infants, unborn babies, pregnant mothers, or elderly
people can be more quickly and severely affected by CO. If you experience
even mild symptoms of CO poisoning, consult your doctor immediately!
F
INDING THE SOURCE OF CO AFTER AN ALARM
C
arbon monoxide is an odorless, invisible gas, which often makes it difficult
to locate the source of CO after an alarm. These are a few of the factors that
can make it difficult to locate sources of CO:
• House well ventilated before the investigator arrives.
• Problem caused by “backdrafting.”
•
Transient CO problem caused by special circumstances.
B
ecause CO may dissipate by the time an investigator arrives, it may be
d
ifficult to locate the source of CO.
B
RK Brands, Inc. shall not be obligated
to pay for any carbon monoxide investigation or service call.
POTENTIAL SOURCES OF CO IN THE HOME
Fuel-burning appliances like:
p
ortable heater, gas or wood
burning fireplace, gas kitchen
range or cooktop, gas clothes dryer.
D
amaged or insufficient venting:
corroded or disconnected water
h
eater vent pipe, leaking chimney pipe
o
r flue, or cracked heat exchanger,
blocked or clogged chimney opening.
I
mproper use of appliance/device:
o
perating a barbecue grill or vehicle
in an enclosed area (like a garage or
s
creened porch).
T
ransient CO Problems:
“
transient” or on-again-off-again CO problems can
be caused by outdoor conditions and other special circumstances.
The following conditions can result in transient CO situations:
1
. Excessive spillage or reverse venting of fuel appliances caused by outdoor
conditions such as:
•
Wind direction and/or velocity, including high, gusty winds. Heavy air in
the vent pipes (cold/humid air with extended periods between cycles).
•
Negative pressure differential resulting from the use of exhaust fans.
• Several appliances running at the same time competing for limited
f
resh air.
•
V
ent pipe connections vibrating loose from clothes dryers, furnaces,
o
r water heaters.
•
O
bstructions in or unconventional vent pipe designs which can amplify
the above situations.
2
. Extended operation of unvented fuel burning devices (range, oven, fireplace).
3.
Temperature inversions, which can trap exhaust close to the ground.
4
. Car idling in an open or closed attached garage, or near a home.
These conditions are dangerous because they can trap exhaust in your home.
S
ince these conditions can come and go, they are
also hard to recreate during
a
CO investigation.
HOW CAN I PROTECT MY FAMILY FROM
CO POISONING?
A
CO Alarm is an excellent means of protection. It monitors the air and
s
ounds a loud alarm before Carbon Monoxide levels become threatening
for average, healthy adults.
A
CO Alarm is not a substitute for pr
oper maintenance of home appliances.
T
o help prevent CO problems and reduce the risk of CO poisoning:
• Clean chimneys and flues yearly. Keep them free of debris, leaves, and
n
ests for pro
per air flow.
Also, have a pro
fessional check for rust and
corrosion, cracks, or separations. These conditions can prevent proper
a
ir movement and cause backdrafting. Never “cap” or cover a chimney
i
n any way that would block air flow.
• Test and maintain all fuel-burning equipment annually. Many local gas
o
r oil companies and HVAC companies offer appliance inspections for
a
nominal fee.
•
Make r
egular visual inspections of all fuel-bur
ning appliances. Check
a
ppliances for excessive rust and scaling. Also check the flame on the
bur
ner and pilot lights. The flame should be blue. A yellow flame
m
eans fuel is not being burned completely and CO may be present.
K
eep the blower door on the furnace closed. Use vents or fans when
they ar
e available on all fuel-bur
n
ing appliances. Make sure
appliances
a
re vented to the outside. Do not grill or barbecue indoors, or in
g
arages or on screen porches.
•
Check for exhaust backflow fr
o
m CO sourc
es. Check the draft hood on
a
n operating furnace for a backdraft. Look for cracks on furnace heat
e
xchangers.
•
Check the house or garage on the other side of shar
ed wall.
•
K
eep windows and doors open slightly.
If you suspect that CO is
escaping into your home, open a window or a door. Opening windows
a
nd doors can significantly decrease CO levels.
In addition, familiarize yourself with all enclosed materials. Read this
manual in its entirety, and make sure you understand what to do if your
C
O Alarm sounds.
REGULATOR
Y INFORMATION FOR
SMOKE/CO ALARMS
REGULATORY INFORMATION FOR CO ALARMS
WHAT LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. Standard UL2034 requires residential CO
Alarms to sound when exposed to levels of CO and exposure times as
described below. They are measured in parts per million (ppm) of CO over
time (in minutes).
UL2034 Required Alarm Points*:
• If the alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN
4 and 15 MINUTES.
•
If the alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN
10 and 50 MINUTES.
• If the alarm is exposed to 70 ppm if CO, IT MUST ALARM BETWEEN
60 and 240 MINUTES.
* Approximately 10% COHb exposure at levels of 10% to 95% Relative
Humidity (RH).
The unit is designed not to alarm when exposed to a constant level
of 30 ppm for 30 days.
CO Alarms are designed to alarm before there is an immediate life threat.
Since you cannot see or smell CO, never assume it’s not present.
• An exposure to 100 ppm of CO for 20 minutes may not affect average,
healthy adults, but after 4 hours the same level may cause headaches.
• An exposure to 400 ppm of CO may cause headaches in average, healthy
adults after 35 minutes, but can cause death after 2 hours.
Standards: Underwriters Laboratories Inc. Single and Multiple Station carbon
monoxide alarms UL2034.
Accor
ding to Underwriters Laboratories Inc. UL2034, Section 1-1.2: “Carbon
monoxide alarms cover
ed by these requirements are intended to respond to the
presence of carbon monoxide from sources such as, but not limited to, exhaust
from internal-combustion engines, abnormal operation of fuel-fired appliances,
and fireplaces. CO Alarms are intended to alarm at carbon monoxide levels
below those that could cause a loss of ability to react to the dangers of Carbon
Monoxide exposure.” This CO Alarm monitors the air at the Alarm, and is
designed to alarm before CO levels become life threatening. This allows you
precious time to leave the house and correct the problem. This is only possible
if Alarms are located, installed, and maintained as described in this manual.
Gas Detection at Typical Temperature and Humidity Ranges: The CO Alarm
is not formulated to detect CO levels below 30 ppm typically. UL tested for false
alarm resistance to Methane (500 ppm), Butane (300 ppm), Heptane (500 ppm),
Ethyl Acetate (200 ppm), Isopropyl Alcohol (200 ppm) and Carbon Dioxide (5000
ppm). Values measure gas and vapor concentrations in parts per million.
Audible Alarm: 85 dB minimum at 10 feet (3 meters).
REGULA
TOR
Y INFORMA
TION FOR SMOKE ALARMS
RECOMMENDED LOCATIONS FOR SMOKE ALARMS
Installing Smoke Alarms in Single-Family Residences
The National Fire Protection Association (NFPA), recommends one Smoke Alarm
on every floor, in every sleeping area, and in every bedroom. In new construction,
the Smoke Alarms must be AC powered and interconnected. See “Agency
Placement Recommendations” for details.
For additional coverage, it is r
ecommended that you install a Smoke Alarm in all
r
ooms, halls, storage ar
eas, finished attics, and basements, where temperatures
normally r
emain between 40˚ F (4˚ C) and 100˚ F (38˚ C). Make sur
e no door or
other obstruction could keep smoke fr
om r
eaching the Smoke Alarms.
Continued...
ABOUT SMOKE ALARMS
B
attery (DC) operated Smoke Alarms:
P
rovide protection even when electricity
f
ails, provided the batteries are fresh and correctly installed. Units are easy to
i
nstall, and do not require professional installation.
A
C powered Smoke Alarms:
C
an be interconnected so if one unit senses
s
moke, all units alarm. They do not operate if electricity fails.
A
C with battery (DC) back-up:
w
ill operate if electricity fails, provided the
b
atteries are fresh and correctly installed. AC and AC/DC units must be installed
b
y a qualified electrician.
S
moke/CO Alarms for Solar or Wind Energy users and battery backup
p
ower systems:
A
C powered Smoke/CO Alarms should only be operated
w
ith true or pure sine wave inverters. Operating this Alarm with most battery-
p
owered UPS (uninterruptible power supply) products or square wave or
“
quasi sine wave” inverters
w
ill damage the Alarm
.
If you are not sure about
y
our inverter or UPS type, please consult with the manufacturer to verify.
S
moke Alarms for the hearing impaired:
S
pecial purpose Smoke Alarms
s
hould be installed for the hearing impaired. They include a visual alarm and an
a
udible alarm horn, and meet the requirements of the Americans With
D
isabilities Act. Can be interconnected so if one unit senses smoke, all units
a
larm.
S
moke alarms are not to be used with detector guards
u
nless the
c
ombination has been evaluated and found suitable for that purpose.
A
ll these Smoke Alarms are designed to provide early warning of fires if located, installed and
c
ared for as described in the user’s manual, and if smoke reaches the Alarm.
I
f you are unsure which type of Smoke Alarm to install, refer the National Fire
P
rotection Association (NFPA) Standard 72 (National Fire Alarm Code) and NFPA
1
01 (Life Safety Code). National Fire Protection Association, One Batterymarch
P
ark, Quincy, MA 02269-9101. Local building codes may also require specific
u
nits in new construction or in different areas of the home.
F
eatures:
• Separate sensors to detect smoke
a
nd CO; the two alarm systems
w
ork independently
• Voice with programmable location
•
Separate audible and visual
signals to indicate alarm levels
of smoke or CO
•
Remote infrared Test/Silence and
programming
•
Powered by two “AA” batteries
•
Side access drawer for easy
battery replacement
All First Alert
®
Smoke Alarms conform to regulatory requirements,
including UL217 and are designed to detect particles of combustion.
S
moke particles of varying number and size are produced in all fires.
Ionization technology is generally more sensitive than photoelectric
technology at detecting small particles, which tend to be produced
i
n greater amounts by flaming fires, which consume combustible
materials rapidly and spread quickly. Sources of these fires may include
paper burning in a wastebasket, or a grease fire in the kitchen.
P
hotoelectric technology is generally more sensitive than ionization
t
echnology at detecting large particles, which tend to be produced in
greater amounts by smoldering fires, which may smolder for hours
b
efore bursting into flame. Sources of these fires may include cigarettes
b
urning in couches or bedding.
For maximum protection, use both types of Smoke Alarms on each
l
evel and in every bedroom of your home.
SPECIAL COMPLIANCE CONSIDERATIONS
This unit alone is not a suitable substitute for complete fire detection
systems in places housing many people—like apartment buildings,
condominiums, hotels, motels, dormitories, hospitals, long-term health
care facilities, nursing homes, day care facilities, or group homes of any
kind—even if they were once single-family homes. It is not a suitable
substitute for complete fire detection systems in warehouses, industrial
facilities, commercial buildings, and special-purpose non-residential build-
ings which require special fire detection and alarm systems. Depending on
the building codes in your area, this unit may be used to provide additional
protection in these facilities.
T
he following information applies to all five types of buildings listed below:
I
n new construction, most building codes require the use of AC or AC/DC
p
owered Smoke Alarms only. AC, AC/DC, or DC powered Smoke Alarms can be
u
sed in existing construction as specified by local building codes. Refer to NFPA
7
2 (National Fire Alarm Code) and NFPA 101 (Life Safety Code), local building
c
odes, or consult your Fire Department for detailed fire protection requirements
i
n buildings not defined as “households.”
1. Single-Family Residence: Single family home, townhouse. It is recommended
this unit be installed on every level of the home, in every bedroom, and in each
bedroom hallway.
2. Multi-Family or Mixed Occupant Residence: Apartment building, condo-
minium. This unit is suitable for use in individual apartments or condos, provided
a primary fire detection system already exists to meet fire detection requirements
in common areas like lobbies, hallways, or porches. Using this unit in common
areas may not provide sufficient warning to all residents or meet local fire
protection ordinances/regulations.
3
. Institutions:
H
ospitals, day care facilities, long-term health care facilities. This
unit is suitable for use in individual patient sleeping/resident rooms, provided a
primary fire detection system already exists to meet fire detection requirements
i
n common areas like lobbies, hallways, or porches. Using this unit in common
a
reas may not provide sufficient warning to all residents or meet local fire
p
rotection ordinances/regulations.
4
. Hotels and Motels:
A
lso boar
d
ing houses and dormitories. This unit is
suitable for use inside individual sleeping/r
e
sident r
o
oms, provided a primary fire
detection system alr
e
ady exists to meet fir
e
detection requirements in common
ar
e
as like lobbies, hallways, or por
c
hes. Using this unit in common areas may
not provide sufficient warning to all residents or meet local fire protection
ordinances/regulations.
5. Warehouses/Commercial Buildings: DO NOT use this Smoke/CO Alarm in
warehouses, industrial or commercial buildings, special-purpose non-residential
buildings, RVs, boats, or airplanes. This Smoke/CO Alarm is specifically designed
for residential use, and may not provide adequate protection in non-residential
applications.
TROUBLESHOOTING GUIDE
If the Alarm... Problem... You should...
H
orn "chirps" about once per minute;
V
o
ice:
"Replace battery in [Location]" every 5 hours
L
ow battery warning. Install two new AA batteries
*.
H
orn sounds three "chirps" every minute;
Voice: "Detector error in [Location, example
"Kitchen"], please see manual" r
epeated every
5 hours; LED has 3 flashes with "chirps".
M
ALFUNCTION SIGNAL.
D
evice is not working
properly, and needs to be replaced.
U
nits under warranty should be returned to
manufacturer for replacement. See “Limited
W
arranty” for details.
Carbon Monoxide Alarm ONLY:
CO Alarm goes back into alarm 4 minutes after you
Silence it.
CO levels indicate a potentially dangerous situation. IF YOU ARE FEELING SYMPTOMS OF CO
POISONING, EV
ACUATE your home and call 911
or the Fire Department. Refer to "If The CO Alarm
Sounds" for details.
CO Alarm sounds frequently even though no high
levels of CO are revealed in an investigation.
The CO Alarm may be improperly located. Refer to
“Where to Install This Alarm” for details.
Relocate your Alarm. If frequent alarms continue,
have home rechecked for potential CO problems.
You may be experiencing an intermittent
CO problem.
Smoke Alar
m ONL
Y
:
Smoke Alarm sounds when no smoke is visible.
Unwanted alarm may be caused by non-emergency
source like cooking smoke.
Silence Alarm using remote control or manual
button; clean the Alarm’s cover with a soft, clean
cloth. If fr
equent unwanted alarms continue,
r
elocate your Alarm. Alarm may be too close to a
kitchen, cooking appliance, or steamy bathroom.
*For a list of acceptable replacement batteries, see “Regular Maintenance.”
If you have questions that cannot be answer
ed by r
eading this manual, call Consumer Af
fairs at 1-800-323-9005, M-F 7:30 a.m. to 5:00 p.m. (CST)
The light flashes GREEN and the horn sounds 5
“chirps” every minute;
V
oice:
"Detector error in [Location, example
"Basement"], please see manual." Repeated every
5 hours.
END OF
LIFE SIGNAL.
Alarm needs to be replaced.
Immediately replace the Alarm.
T
his Smoke/CO Alarm is intended for residential use. It is not intended for use in
i
ndustrial applications where Occupational Safety and Health Administration
(
OSHA) requirements for Carbon Monoxide Alarms must be met. The Smoke
A
larm portion of this device is not intended to alert hearing impaired residents.
S
pecial purpose Smoke Alarms should be installed for hearing impaired residents
(
CO Alarms are not yet available for the hearing impaired).
Smoke/CO Alarms may not waken all individuals. Practice the escape plan
at least twice a year, making sure that everyone is involved – from kids to grand-
parents. Allow children to master fire escape planning and practice before holding
a fire drill at night when they are sleeping. If children or others do not readily
waken to the sound of the Smoke/CO Alarm, or if there are infants or family
members with mobility limitations, make sure that someone is assigned to assist
them in fire drill and in the event of an emergency. It is recommended that you
hold a fire drill while family members are sleeping in order to determine their
response to the sound of the Smoke/CO Alarm while sleeping and to determine
whether they may need assistance in the event of an emergency.
S
moke
/
CO
A
lar
m
s cannot work without power
.
B
attery operated units cannot
w
ork if the batteries ar
e
missing, disconnected or dead, if the wr
ong type of batteries
a
r
e
used, or if the batteries ar
e not installed corr
ectly
. AC units cannot work if the AC
p
ower is cut of
f
for any r
eason (open fuse or cir
cuit br
eaker
,
failure along a power
l
ine or at a power station, electrical fir
e
that bur
ns the electrical wir
es, etc.). If you ar
e
c
oncer
n
ed about the limitations of battery or AC power
, install both types of units.
This Smoke/CO Alar
m
will not sense smoke or CO that does not r
e
ach the
sensors. It will only sense smoke or CO at the sensor
.
Smoke or CO may be
pr
e
sent in other ar
e
as. Doors or other obstructions may af
f
ect the rate at which
CO or smoke r
e
aches the sensors. If bedr
o
om doors ar
e
usually closed at night,
we r
e
commend you install an alarm device (Combination CO and Smoke Alarm,
or separate CO Alarms and Smoke Alarms) in each bedr
o
om and in the hallway
between them.
T
his Smoke/CO Alarm may not sense smoke or CO on another level of the
h
ome.
E
xample: This alarm device, installed on the second floor, may not sense
s
moke or CO in the basement. For this reason, one alarm device may not give
a
dequate early warning. Recommended minimum protection is one alarm
d
evice in every sleeping area, every bedroom, and on every level of your home.
S
ome experts recommend battery powered Smoke and CO Alarms be used in
c
onjunction with interconnected AC powered Smoke Alarms. For details, see
“
About Smoke Alarms” for details.
Smoke/CO Alarms may not be heard. The alarm horn loudness meets or
exceeds current UL standards of 85 dB at 10 feet (3 meters). However, if the
Smoke/CO Alarm is installed outside the bedroom, it may not wake up a sound
sleeper or one who has recently used drugs or has been drinking alcoholic
beverages. This is especially true if the door is closed or only partly open. Even
persons who are awake may not hear the alarm horn if the sound is blocked by
distance or closed doors. Noise from traffic, stereo, radio, television, air condi-
tioner, or other appliances may also prevent alert persons from hearing the alarm
horn. This Smoke/CO Alarm is not intended for people who are hearing impaired.
T
he Alar
m
may not have time to alar
m befor
e the fir
e itself causes damage,
i
njur
y
, or death, since smoke fr
om some fir
es may not r
e
ach the unit imme-
d
iately
.
Examples of this include persons smoking in bed, childr
en playing
w
ith matches, or fir
e
s caused by violent explosions r
esulting fr
om escaping
g
as.
This Smoke/CO Alar
m
is not a substitute for life insurance.
Though this
Smoke/CO Alarm war
n
s against incr
e
asing CO levels or the pr
e
sence of smoke,
BRK Brands, Inc. does not warrant or imply in any way that they will pr
o
tect lives.
Homeowners and r
e
nters must still insur
e
their lives.
T
his Smoke/CO Alarm has a limited life.
A
lthough this Smoke/CO Alarm and all
o
f its parts have passed many stringent tests and are designed to be as reliable
a
s possible, any of these parts could fail at any time. Therefore, you must test
t
his device weekly. The unit should be replaced immediately if it is not operating
p
roperly.
This Smoke/CO Alarm is not foolproof. Like all other electronic devices, this
Smoke/CO Alarm has limitations. It can only detect smoke or CO that reaches
the sensors. It may not give early warning of the source of smoke or CO is in a
remote part of the home, away from the alarm device.
G
ENERAL LIMITA
TIONS OF SMOKE/CO ALARMS
USER’S MANUAL
M
ore specifically, install Smoke Alarms:
•
On every level of your home, including finished attics and basements.
• Inside every bedroom, especially if people sleep with the door partly or
c
ompletely closed.
•
In the hall near every sleeping area. If your home has multiple sleeping
a
reas, install a unit in each. If a hall is more than 40 feet long (12 meters),
install a unit at each end.
•
At the top of the first-to-second floor stairway, and at the bottom
of the basement stairway.
S
pecific requirements for Smoke Alarm installation vary from state to state
a
nd from region to region. Check with your local Fire Department for current
requirements in your area.
It is recommended AC or AC/DC units be inter-
c
onnected for added protection.
I
NSTALLING SMOKE ALARMS IN MOBILE HOMES
For minimum security install one Smoke Alarm as close to each sleeping area as
p
ossible. For more security, put one unit in each room. Many older mobile homes
(
especially those built before 1978) have little or no insulation. If your mobile
home is not well insulated, or if you are unsure of the amount of insulation, it is
i
mportant to install units on inside walls only. Smoke Alarms should be installed
w
here temperatures normally remain between 40˚ F (4˚ C) and 100˚ F (38˚ C).
A
GENCY PLACEMENT RECOMMENDATIONS
S
tandards:
U
nderwriters Laboratories Inc. Single and Multiple Station Smoke
A
larms 217.
N
FPA 72 (National Fire Code) Chapter 11
“
For your information, the National Fire Protection Association's Standard 72,
reads as follows:”
“
11.5.1 One- and Two-Family Dwelling Units.”
“
11.5.1.1 Smoke Detection.
W
here required by applicable laws, codes, or
standards for the specified occupancy, approved single- and multiple-station
S
moke Alarms shall be installed as follows: (1) In all sleeping r
ooms.
E
xception: Smoke Alarms shall not be required in sleeping rooms in existing
one- and two-family dwelling units. (2) Outside of each separate sleeping
a
rea, in immediate vicinity of the sleeping rooms. (3) On each level of the
d
welling unit, including basements. Exception: In existing one- and two family
dwelling units, approved Smoke Alarms powered by batteries are permitted.”
“
A.11.8.3 Are More Smoke Alarms Desirable?
T
he required number of
S
moke Alarms might not pro
vide reliable early warning protection for those
areas separated by a door from the areas protected by the required Smoke
A
larms. For this reason, it is recommended that the householder consider
t
he use of
a
dditional Smoke Alarms for those are
as for increased protection.
The additional
areas include the basement, bedrooms, dining room, furnace
r
oom, utility room, and hallways not protected by the required Smoke Alarms.
T
he installation of Smoke Alarms in kitchens, attics (finished or unfinished),
or garages is not normally r
ecommended, as these locations occasionally
e
xperience conditions that can result in improper operation.”
C
alifornia State Fire Marshal (CSFM)
E
arly warning detection is best achieved by the installation of fire detection
e
quipment in all rooms and areas of the household as follows: A Smoke Alarm
i
nstalled in each separate sleeping area (in the vicinity, but outside bedrooms),
a
nd Heat or Smoke Alarms in the living rooms, dining rooms, bedrooms,
kitchens, hallways, finished attics, fur
n
ace ro
oms, closets, utility and storage
r
ooms, basements, and attached garages.
For First T
ime and When Changing Batteries
W
HAT YOU WILL SEE AND HEAR WITH THIS ALARM, Continued
I
f Alarm is Not Operating Properly
V
oice:
“
Detector error in [Location, example “Kitchen”], please see
manual.” Repeated every 5 hours
H
orn:
3
chirps every minute
P
ower/Smoke LED:
T
hree Flashes approximately once a minute
C
O LED:
O
ff
A
larm has reached its End of Life
V
oice:
“
Detector error in [Location, example “Basement”], please see
manual.” Repeated every 5 hours
H
orn:
5
chirps every minute
P
ower/Smoke LED:
F
ive Flashes approximately once a minute
CO LED: Off
Alarm Levels of CO are Detected
Voice:
“Warning, evacuate carbon monoxide in [Location, example:
“
Kitchen”]. Evacuate.” “
_
___ ppm.”
H
orn:
4
beeps, pause, 4 beeps, voice
*
Power/Smoke LED:
Off
CO LED: Flashes Red
*
NOTE:
I
f unit goes into CO alarm, the regular 4 beeps-brief pause cycle will
r
epeat for four minutes. After four minutes, the pause will increase to one minute.
Smoke is Detected
V
oice:
“
Warning, evacuate smoke in [Location, example: “Kitchen”].
E
vacuate.”
H
orn:
3
beeps, pause, 3 beeps, voice
Power/Smoke LED: Flashes Red
CO LED: Off
Smoke Alarm is Silenced
Voice: Silent.
H
orn:
O
ff
P
ower/Smoke LED:
F
lashes Red
CO LED: Off
CO Alarm is Silenced
Voice: Silent.
H
orn:
O
ff
P
ower/Smoke LED:
O
ff
CO LED: Flashes Red
WHA
T YOU WILL SEE AND HEAR WITH THIS ALARM
Under Normal Operations
Voice:
Silent Power/Smoke LED: Flashes Green once a
minute
Horn: Silent CO LED: Off
When Y
ou T
est the Alar
m
Voice:
“Testing.” “Warning, evacuate smoke in [Location, example:
“Kitchen”]. Evacuate.”
Horn: 3 beeps, pause, 3 beeps, voice
Power/Smoke LED: Flashes Red
CO LED: Of
f
followed by
Voice: “Warning, evacuate carbon monoxide in [Location, example:
“Kitchen”]. Evacuate.”
Horn: 4 beeps, pause, 4 beeps, voice
Power/Smoke LED: Off
CO LED: Flashes Red
If Battery Becomes Low or is Missing
Voice:
“Replace battery in [Location, example “Kitchen”].” Repeated
every 5 hours
Horn: chirps once a minute
Power/Smoke LED: Flashes approximately once a minute
CO LED: Of
f
Action:
1. Insert batteries (2, AA batteries).
Alarm Will Say:
“Welcome, First Alert Carbon
Monoxide and Smoke Alarm.”
“No location programmed” if
first
time
or “[Location, example:
“Kitchen”] location programmed”
when changing batteries.
“To select location, press and hold
test button now.”
2. Press & Hold Test Button, or use
your IR remote control’s channel
or volume button, if you would like
to program the location or change
the location of the Alarm. Release
button after Alarm responds.
“To save location, press and hold
test button after location is heard.”
Alarm will speak list of locations
(see below).
3. After you hear the location of
where you are placing the Alarm,
Press & Hold the Test Button or
use your IR r
emote contr
ol’
s
channel or volume button.
“[Location, example: “Kitchen”]
location saved.”
If no location is chosen: “No location
saved.”
Your Alarm has now been programmed for the location of your choice.
A
vailable locations:
Basement
Hallway
Office
Child’s Bedroom Kitchen Utility Room
Dining Room Living Room
Family Room Master Bedroom
Guest Bedroom No Location
INSTALLATION
WHERE TO INSTALL THIS ALARM
M
inimum coverage for Smoke Alarms
,
as recommended by the National
Fire Protection Association (NFPA), is one Smoke Alarm on every floor, in
every sleeping area, and in every bedroom (See “Regulatory Information For
S
moke Alarms” for details on the NFPA recommendations).
For CO Alarms, the National Fire Protection Association (NFPA) recommends
t
hat a CO Alarm should be centrally located outside of each separate sleeping
a
rea in the immediate vicinity of the bedrooms. For added protection, install
additional CO Alarms in each separate bedroom, and on every level of your
h
ome.
NOTE: For added protection, install an additional Smoke/CO Alarm at least
15 feet (4.6 meters) away from the furnace or fuel burning heat source where
p
ossible. In smaller homes or in manufactured homes where this distance cannot
b
e maintained, install the Alarm as far away as possible from the furnace or
o
ther fuel burning source. Installing the Alarm closer than 15 feet (4.6 meters)
will not harm the Alarm, but may increase the frequency of unwanted alarms.
I
n general, install combination Smoke and Carbon Monoxide Alarms:
•
O
n every level of your home, including finished attics and basements.
• Inside every bedroom, especially if people sleep with the door partly or
c
ompletely closed.
• In the hall near every sleeping area. If your home has multiple sleeping
a
reas, install a unit in each. If a hall is more than 40 feet (12 meters) long,
i
nstall a unit at each end.
•
At the top of first-to-second floor stairs.
•
At the bottom of the basement stairs.
•
For additional coverage, install Alarms in all rooms, halls, and storage
a
reas, where temperatures normally remain between 40˚ F and 100˚ F
(
4˚ C and 38˚ C).
R
ecommended Placement
•
When installing on the wall, the top edge of Smoke Alarms should be
placed between 4 inches (102 mm) and 12 inches (305 mm) fr
om the
w
all/ceiling line.
•
W
hen installing on the ceiling, place the alarm as close to the center as
possible.
•
In either case, install at least 4 inches (102 mm) from where the wall and
c
eiling meet. See “Avoiding Dead Air Spaces” for more information.
NOTE: For any location, make sur
e no door or other obstruction could keep
c
arbon monoxide or smoke from reaching the Alarm.
Installing Smoke/CO Alar
ms in Mobile Homes
F
or minimum security install one Smoke/CO Alarm as close to each sleeping
area as possible. For more security, put one unit in each room. Many older
m
obile homes (especially those built before 1978) have little or no insulation.
I
f your mobile home is not well insulated, or if you are unsure of the amount
of insulation, it is important to install units on inside walls only.
WHERE THIS ALARM SHOULD NOT BE INSTALLED
Do NOT locate this Smoke/CO Alarm:
•
I
n a location where
it could be easily triggered when using your remote to
operate your TV, VCR, etc.
• In garages, furnace rooms, crawl spaces and unfinished attics. Avoid
extremely dusty, dirty or greasy areas.
•
Where combustion particles are pr
oduced. Combustion particles form
when something burns. Areas to avoid include poorly ventilated kitchens,
garages, and furnace rooms. Keep units at least 20 feet (6 meters) from
the sour
ces of combustion particles (stove, furnace, water heater, space
heater) if possible. In areas where a 20-foot (6 meter) distance is not
possible – in modular, mobile, or smaller homes, for example – it is
r
ecommended the Smoke Alarm be placed as far from these fuel-burning
sources as possible. The placement recommendations are intended to
keep these Alarms at a reasonable distance from a fuel-burning source,
and thus reduce “unwanted” alarms. Unwanted alarms can occur if a
Smoke Alarm is placed directly next to a fuel-burning source. Ventilate
these ar
eas as much as possible.
• Within 5 feet (1.5 meters) of any cooking appliance. In air streams near
kitchens. Air currents can draw cooking smoke into the smoke sensor
and cause unwanted alarms.
• In extremely humid areas. This Alarm should be at least 10 feet (3 meters)
from a shower, sauna, humidifier, vaporizer, dishwasher, laundry room,
utility room, or other source of high humidity.
•
In dir
ect sunlight.
• In turbulent air, like near ceiling fans or open windows. Blowing air may
pr
event CO or smoke fr
om reaching the sensors.
• In areas where temperature is colder than 40˚ F (4˚C) or hotter than 100˚ F
(38˚C). These ar
eas include non-airconditioned crawl spaces, unfinished
attics, uninsulated or poorly insulated ceilings, por
ches, and garages.
• In insect infested areas. Insects can clog the openings to the sensing
chamber.
•
Less than 12 inches (305 mm) away fr
om fluor
escent lights. Electrical
“noise” can interfere with the sensor.
• In “dead air” spaces. See “Avoiding Dead Air Spaces”.
HOW TO INSTALL THIS ALARM
This combination Smoke/CO Alarm was designed to be mounted on the
ceiling or wall. It is not a tabletop device.
You must install this device on the
c
eiling or wall as outlined below. Read “Where To Install This Alarm” before
starting.
T
ools you will need:
p
encil, drill with 3/16” or 5mm drill bit,
f
lathead screwdriver, hammer.
•
Do not install this unit over an electrical junction box. Air currents
around junction boxes can prevent smoke from reaching the
s
ensing chamber and prevent the unit from alarming. Only AC
p
owered units are intended for installation over junction boxes.
If you want to lock the battery compartment, or lock the Smoke/CO
Alarm to the mounting bracket, please read the “Optional Locking
F
eatures” section in the “Programming Guide” attachment before you
begin installation.
1. Hold base firmly and twist the mounting bracket counterclockwise (left) to
s
eparate it from the unit.
2. Hold the mounting bracket against the ceiling (or wall) so the vertical
m
ounting slot is aligned in the 12 o’clock position and trace around the
inside of the mounting slots (vertical and horizontal mounting).
3
. Put the unit where it won’t get covered with dust when you drill the
mounting holes.
4
. Using a 3/16” (5 mm) drill bit, drill a hole through the center of the oval
outlines you traced.
5
. Insert the plastic screw anchors (in the plastic bag with screws) into the
holes. Tap the screw anchors gently with a hammer, if necessary, until
they are flush with the ceiling or wall.
6
. Line the mounting bracket up over the plastic screw anchors.
7
. Screw the mounting bracket to the ceiling or wall through the mounting
slots using the two scr
ews provided.
8
.
Before attaching the Alarm to
t
he bracket, insert the two (2)
AA batteries (included) into the
b
attery compartment. Match
t
he terminals on the end of the
battery with the terminals on
t
he unit. Match “+” to “+” and
“
-” to “-.” If the batteries are
not fully inserted, the unit
c
annot re
ceive battery power.
NOTE: The unit may beep briefly when you install the batteries. This is normal.
T
he GREEN Light flashes about every 60 seconds when the unit is
r
eceiving battery power.
T
he battery door will resist closing unless batteries are installed. This
warns you the unit will not operate without batteries.
9
. Attach the Smoke/CO Alarm to the mounting
b
racket. Line up the guides on the alarm’s
b
ase with the guides on the mounting bracket.
When guides are lined up, turn the base
c
lockwise (right) until it snaps into place.
N
OTE: Once the Smoke Alarm is snapped
o
nto the mounting bracket, you can rotate
the Smoke Alarm to adjust the alignment.
1
0. Test the Smoke/CO Alarm. See “Weekly
Testing” for details.
IF YOUR SMOKE/CO ALARM SOUNDS
WHAT TO DO FIRST–IDENTIFY THE TYPE OF ALARM
S
UGGESTED AREAS FOR INSTALLING 
S
MOKE ALARMS, CO ALARMS, AND COMBO UNITS
SMOKE ALARM WITH 
SILENCE FEATURE
CO ALARMS
BOTH, OR COMBINATION 
SMOKE/CO ALARMS
SMOKE ALARMS
KEY:
Suggested locations are based on
NFPA recommendations (NFPA 72 
for Smoke Alarms and NFPA 720 for
Carbon Monoxide Alarms). Always 
refer to national and local codes 
b
efore beginning any installation.
In new construction AC and AC/DC smoke alarms MUST
be interconnected to meet NFPA recommendations.
T
ype of Alarm
C
arbon Monoxide (CO)
W
hat You See and Hear
V
oice:
“
Warning, evacuate carbon
m
onoxide in [Location,
example: “Kitchen”]. Evacuate.”
“
_
___ ppm.”
Horn: 4 beeps, pause, 4 beeps, voice
P
ower/Smoke LED
:
Off
CO LED: Flashes Red
S
moke
V
oice:
“
Warning, evacuate smoke in
[Location, example: “Kitchen”].
E
vacuate.”
Horn: 3 beeps, pause, 3 beeps, voice
P
ower/Smoke LED
:
Flashes Red
CO LED: Off
IF THE CO ALARM SOUNDS
Actuation of your CO Alarm indicates the presence of carbon monoxide
(
CO) which can kill you. In other words, when your CO Alarm sounds, you
m
ust not ignore
it!
I
F THE CO ALARM SIGNAL SOUNDS:
1.
Operate the T
est/Silence button.
2.
Call your emer
gency services, fir
e department or 911. W
rite down the
n
umber of your local emergency service here:
__________________________________________________________________
3. Immediately move to fresh air—outdoors or by an open door or window.
Do a head count to check that all persons ar
e accounted for
. Do not r
e-
e
nter the premises, or move away from the open door or window until the
emergency services responder has arrived, the premises have been aired
out, and your CO Alarm remains in its normal condition.
4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour
period, repeat steps 1-3 and call a qualified appliance technician to inves-
tigate for sources of CO from fuel-burning equipment and appliances, and
inspect for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately. Note any
combustion equipment not inspected by the technician, and consult the
manufacturers’ instructions, or contact the manufacturers directly, for more
information about CO safety and this equipment. Make sure that motor
vehicles are not, and have not, been operating in an attached garage or
adjacent to the residence. Write down the number of a qualified appliance
technician here:
__________________________________________________________________
NOTE: A qualified appliance technician is defined as “a person, firm,
corporation, or company that either in person or through a representative, is
engaged in and responsible for the installation, testing, servicing, or replace-
ment of heating, ventilation, air conditioning (HVAC) equipment, combustion
appliances and equipment, and/or gas fir
eplaces or other decorative
combustion equipment.”
“ALARM-MOVE TO FRESH AIR”
I
f you hear the CO alarm horn and the CO red light is flashing, move
e
very
one to a sourc
e of fre
sh air.
DO NOT remove the batteries!
AFTER AN ALARM
After the emergency responders arrive, the premises aired out, and your CO
Alarm remains in its normal condition, you can check what the highest carbon
monoxide level sensed was:
Action:
1. Press & Hold Test Button
Alar
m W
ill Say:
“Highest carbon monoxide level was
___ ppm. Please see manual.”
“T
o clear highest carbon monoxide
level, pr
ess and hold test button
now.”
2.
Press & Hold Test Button, if you
would like to clear the highest
level sensed.
If you would like to keep the
highest level in memory, do not
press anything.
“Highest carbon monoxide level
clear
ed.”
Alarm will say nothing.
W
HAT TO DO IN CASE OF FIRE, Continued
•
Feel doors with the back of your hand before opening them.
I
f a door is cool, open it slowly. Don’t open a hot door. Keep doors
and windows closed, unless you must escape through them.
•
Cover your nose and mouth with a cloth (preferably damp).
Take short, shallow breaths.
•
Meet at your planned meeting place outside your home,
and do a head count to make sure everybody got out safely.
•
Call the Fire Department as soon as possible from outside.
Give your address, then your name.
•
Never go back inside a burning building for any reason.
• Contact your Fire Department for ideas on making your home safer.
Alarms have various limitations. See "General Limitations of Smoke/CO
A
larms" for details.
USING THE SILENCE FEATURES
Never remove the batteries to quiet an unwanted alarm. Removing the
b
atteries disables the alarm and removes your protection.
T
he Silence Feature is intended to temporarily silence the horn while you
identify and correct the problem. Do not use the Silence Feature in emergency
s
ituations. It will not correct a CO problem or extinguish a fire.
T
he Silence Feature can temporarily quiet an unwanted alarm for several
minutes. You can silence this Smoke/CO Alarm two ways:
1
.
M
anually:
P
ress the Test/Silence button on the alarm cover for at least
3
-5 seconds.
2.
Using Your Remote Control: See section “OPERATING THIS ALARM
U
SING YOUR IR REMOTE CONTROL”.
A
fter the Test/Silence or remote control button is released, the Red LED
b
links during the silence mode.
S
ILENCING THE LOW BA
TTER
Y W
ARNING
T
his silence feature can temporarily quiet the low battery war
ning “chirp” for
u
p to 8 hours. You can silence the low battery warning “chirp” two ways:
1
. M
anually:
P
ress the Test/Silence button on the alarm cover.
2
.
U
sing Your Remote Control:
S
ee section “OPERATING THIS ALARM
USING YOUR IR REMOTE CONTROL”.
Once the low battery war
n
ing “chirp” silence feature
is activated, the unit
c
ontinues to flash the Green light once a minute for 8 hours. After 8 hours,
t
he low battery “chirp” will resume.
R
eplace the batteries as soon as
possible; this unit will not operate without battery power!
T
o
deactivate this feature:
P
re
ss the Test/Silence button or use your remote
control again. The unit will go into Test Mode and the low battery warning will
r
esume (LED flashes and unit sounds “chirp” once a minute).
SILENCING THE END OF LIFE SIGNAL
T
his silence feature
can temporarily quiet the End of Life warn
ing “chirp” for
up to 2 days. You can silence the End of Life warning “chirp” by pressing the
T
est/Silence button. The horn will chirp, acknowledging that the End of Life
s
ilence feature has been activated.
A
fter appro
ximately 2 days, the End of Life “chirp” will re
sume.
After approximately 2-3 weeks the End of Life warning cannot be silenced.
WEEKLY TESTING
•
NEVER use an open flame of any kind to test this unit. You might
accidentally damage or set fire to the unit or to your home. The
b
uilt-in test switch accurately tests the unit’s
operation as re
quired
by Underwriters Laboratories, Inc. (UL). NEVER use vehicle exhaust!
Exhaust may cause permanent damage and voids your warranty.
•
DO NOT stand close to the Alarm when the horn is sounding.
Exposure at close range may be harmful to your hearing. When
testing, step away when horn starts sounding.
It is important to test this unit every week to make sure it is working
properly. Using the test button is the recommended way to test this
S
moke/CO Alarm
.
Y
o
u can test this Smoke/CO Alarm two ways:
1. Manually: Press and hold the Test/Silence button on the
A
larm cover until Alarm
V
oice
s
ays “Testing” (typically
3-5 seconds).
2
. Using Your Remote Control:
S
ee section “OPERATING
THIS ALARM USING YOUR IR REMOTE CONTROL”.
During testing, you will see and hear the following sequence:
• The Alarm
Voice will say “Testing.” The Horn will
sound 3 beeps, pause, 3 beeps. The Alarm
Voice will say “Warning,
evacuate smoke in [Location, example: “Kitchen”]. Evacuate.” The
Power/Smoke LED flashes Red and the CO LED will be Off.
•
Next the Horn will sound 4 beeps, pause, 4 beeps. The Alarm V
oice
will say “Warning, evacuate carbon monoxide in [Location, example:
“Kitchen”]. Evacuate.” The Power/Smoke LED will be Off and the CO
LED
flashes Red.
If the unit does not alarm, make sure the batteries are correctly installed, and
test again. If the unit still does not alarm, r
eplace it immediately.
2
1
REGULAR MAINTENANCE
This unit has been designed to be as maintenance-free as possible, but there
are a few simple things you must do to keep it working properly.
Use only the replacement batteries listed below. The unit may not
operate pr
operly with other batteries. Never use rechargeable batteries
since they may not pr
ovide a constant char
ge.
•
T
est it at least once a week.
• Clean the Smoke/CO Alarm at least once a month; gently vacuum the
outside of the Smoke/CO Alarm using your household vacuum’
s soft
brush attachment. A can of clean compr
essed air (sold at computer or
office supply stores) may also be used. Follow manufacturer instructions
for use. Test the Smoke/CO Alarm. Never use water, cleaners or solvents
since they may damage the unit.
• If the Smoke/CO Alarm becomes contaminated by excessive dirt, dust
and/or grime, and cannot be cleaned to avoid unwanted alarms, replace
the unit immediately
.
• Relocate the unit if it sounds frequent unwanted alarms. See “Where This
Alarm Should Not Be Installed” for details.
Choosing a r
eplacement battery:
Your Smoke/CO Alarm requires two standard AA alkaline batteries. The
following batteries are acceptable as replacements: Eveready Energizer E91.
These batteries are available at many local retail stores.
Actual battery service life depends on the Smoke/CO Alarm and the environ-
ment in which it is installed. All the batteries specified above are acceptable
r
eplacement batteries for this unit. Regar
dless of the manufactur
er’s suggested
battery life, you MUST replace the battery immediately once the unit starts
“chirping” (the “low battery warning”).
PARTS OF THIS SMOKE/CO ALARM
1
Test/Silence Button and Remote
Control Sensor
2
Battery Compartment
3
Power/Smoke Alarm LED
4 CO Alarm LED
W
hen the Smoke Alarm is Silenced When the CO Alarm is Silenced
T
he Smoke Alarm will remain silent
f
or up to 15 minutes, then return to
normal operation.
If the smoke has not clear
ed–or
c
ontinues to increase–the device
w
ill go back into alarm.
T
he CO alarm will remain silent for
u
p to 4 minutes.
A
fter 4 minutes, if CO levels remain
p
otentially dangerous the horn will
s
tart sounding again.
T
o replace the batteries (without removing Alarm from the ceiling or wall):
1. Open the battery compartment.
2. Press tabs A and B as shown in the diagram
and remove each battery.
3. Insert the new batteries, making sure they
snap completely into the battery compartment.
Match the terminals on the ends of the
batteries with the terminals on the unit.
4. Close the battery compartment, and then test
the unit by pr
essing the T
est/Silence button or
by using your remote control.
NOTE: See section “OPERATING THIS ALARM USING YOUR IR REMOTE
CONTROL” for important information on disabling and enabling the IR
feature.
A
B
LISTED TO
UL 217
A
ND
U
L 2034
S
TANDARDS
A
VOIDING DEAD AIR SP
ACES
“Dead air” spaces may pr
event smoke from reaching the Smoke/CO Alarm.
T
o avoid dead air spaces, follow installation r
ecommendations below
.
On ceilings, install Smoke/CO Alarms as close to the center of the ceiling as
possible. If this is not possible, install the Smoke/CO Alarm at least 4 inches
(102 mm) fr
om the wall or cor
ner
.
For wall mounting (if allowed by building codes), the top edge of Smoke/CO
Alarms should be placed between 4 inches (102 mm) and 12 inches (305 mm)
from the wall/ceiling line, below typical “dead air” spaces.
On a peaked, gabled, or cathedral ceiling, install first Smoke/CO Alarm
within 3 feet (0.9 meters) of the peak of the ceiling, measured horizontally.
Additional Smoke/CO Alarms may be required depending on the length, angle,
etc. of the ceiling's slope. Refer to NFP
A 72 for details on requirements for
sloped or peaked ceilings.
LIMITED WARRANTY
BRK Brands, Inc., ("BRK") the maker of First Alert
®
brand products warrants that for a period of seven years from the date of purchase, this product will be free from defects
in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of
equal or greater value. This is your exclusive warranty. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do not
have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current,
use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the warranty does not cover
Acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that are included with this unit.
BRK shall not be liable for any incidental or consequential damages
caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular
purpose is limited in duration to the duration of the above warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state or province to province.
How to Obtain Warranty Service
Ser
vice:
If service is r
equired, do not return the product to your retailer. In order to obtain warranty service, contact the Consumer Affairs Division at 1-800-323-9005,
7:30 AM - 5:00 PM Central Standar
d Time, Monday through Friday. To assist us in serving you, please have the model number and date of purchase available when calling.
For W
arranty Service return to:
25 Spur Drive, El Paso, TX 79906
Battery: BRK Brands, Inc. make no warranty, express or implied, written or oral, including that of merchantability or fitness for any particular purpose with respect to battery.
For your records, please record:
Date Pur
chased: __________________ Wher
e Pur
chased: ______________________ Date Installed: ____________/____________Month/Y
ear
Replace alarm 7 years after installation. Please write the date in the space provided:
_____________/____________Month/Year
The alarm will also provide an audible End-of-Life Signal approximately 7 years after installation to remind you to replace the unit.
The End-of-Life Signal can be silenced for up to 2 days. Do not unplug the alarm or remove the batteries until you get replacement.
IF THE SMOKE ALARM SOUNDS
RESPONDING TO AN ALARM
• If the unit alarms and you are not testing the unit, it is warning you
of a potentially dangerous situation that requires your immediate
attention. NEVER ignore any alarm. Ignoring the alarm may result in
injury or death.
• Never remove the batteries from a battery operated Smoke/CO
Alarm to stop an unwanted alarm (caused by cooking smoke, etc.).
Removing batteries disables the alar
m so it cannot sense smoke,
and removes your protection. Instead open a window or fan the
smoke away from the unit. The alarm will reset automatically.
• If the unit alarms get everyone out of the house immediately.
WHAT TO DO IN CASE OF FIRE
•
Don’
t panic; stay calm. Follow your family escape plan.
• Get out of the house as quickly as possible. Don’t stop to get
dressed or collect anything.
OPERATING THIS ALARM USING YOUR IR REMOTE
C
ONTROL
This alarm can be operated using most household IR remote controls. Most
functions can be controlled including testing, silencing the alarm, silencing
t
he low battery chirp and programming the alarm. The following procedure is
the same for all functions: Standing no further than 20 feet (6 meters) away
from the alarm, aim your IR remote at the alarm and press the CHANNEL or
V
OLUME button for at least 3-5 seconds. Depending on what mode your
alarm is in, these actions will cause the alarm to respond appropriately. If the
alarm does not respond to your remote control, there may be an obstruction
b
etween you and the alarm, you may be standing too far away, or your remote
control may not be compatible.
HOW TO DISABLE THE IR REMOTE CONTROL FEATURE
Y
ou may need to disable the IR Remote Control feature because your alarm is
l
ocated in an area that is in the path of your remote control and is setting off
the alarm unintentionally. If alarm cannot be re-located to an optimal location,
f
ollow these steps:
1
) Open the battery drawer.
2
) While holding down the test button, close the battery drawer. You will hear
a
chirp. Your IR Remote Control feature is now disabled.
Note: You can re-enable your IR Remote Control feature by opening the
b
attery drawer and closing it WITHOUT holding down the test button.
R
emember, when you change batteries, you must follow the steps above to
keep the IR Remote Control feature disabled.
4