Filter
Top Products
en en
english
Bosch Solar Module c-Si M 60 IN30125
Bosch Solar Energy AG
Bosch Solar Module c-Si M 60 IN30125
Bosch Solar Energy AG
Table of Contents
Disclaimer of liability I General information | 32 | Table of Contents I Introduction
1 Introduction 2
2 Disclaimer of liability 3
3
General information 3
4
General safety 4
5
Installation 5
6
Specifications 9
7
Wiring 9
8
Grounding 10
9
Diodes 11
10
Maintenance 11
11
Disposal 11
This manual contains information regarding installation,
operation, maintenance and safety handling of Bosch
Solar Energy AG photovoltaic modules. Before installation
or using the PV modules, it is important to read this man-
ual and understand the instructions carefully.
1 Introduction
2 Disclaimer of liability
3 General information
Since the use of this Installation, Operation and Mainte-
nance Manual and the conditions of installation, opera-
tion, use and maintenance of the module are beyond
Bosch Solar Energy AG control, Bosch Solar Energy AG
does not assume responsibility and expressly disclaims
liability for loss, damage, injury or expense arising out of
or in anyway connected with such installation, operation,
use or maintenance of the module.
Bosch Solar Energy AG assumes no responsibility for any
infringement of patents or other rights of third parties
that may result from use of the module. No license is
granted by implication or otherwise under any patent or
patent rights.
The information in this Manual is based on Bosch Solar
Energy AG knowledge and experience and is believed to
be reliable; but such information including product spec-
ifications (without limitations) and suggestions do not
constitute a warranty, expressed or implied. Bosch Solar
Energy AG reserves the right to make changes to the
product, specifications or this manual without prior
notice.
For your safety and the safety of others, please read the
entire Installation, Operation and Maintenance Manual
carefully prior to installing, wiring, operating and per-
forming maintenance of PV modules. Also, carefully read
To avoid the hazard of electric shock and injury when
installing, wiring, operating and maintaining the PV mod-
ules
The installation of solar PV modules requires a great
degree of skill and DC voltage exceeds 100 V, it only be
performed by a qualified licensed professional, including,
without limitation, licensed contractors and licensed
electricians. The installer assumes the risk of all injury
that might occur during installation, including without
limitation, the risk of electric shock.
Important Notice!
Important Notice!
the Module Data Sheet provided with this product. De-
termine local permits, installation and inspection re-
quirements before installing module(s). If not otherwise
specified, it is recommended that the requirements of
the U.S. National Electric Code (NEC) be followed.
This photovoltaic module produces electricity when
exposed to the sunlight, even at low light levels or when
other sources illuminate the front face. The electrical
hazard from the voltage and current of a single module is
low. However, the voltage increases as modules are
connected in series and the available current increases
as the modules are connected in parallel. Thus, for a
module connected within a system, contact with electri-
cally active parts of the module such as terminals can
result in lethal shock, sparks, and burns. The only way to
eliminate this hazard is to prevent exposure of the
module(s) to light.
Cover the entire front surface of the PV modules with
a dense, opaque material such as the cardboard box,
during installation and handling of the modules.
Do not expose Back sheet foil directly to sunlight
Work only under dry conditions, with dry modules
and tools.
Be sure to completely ground all modules.
Since sparks may occur, do not install the module
where flammable gases or vapors are present.
Module installation and operation should be per-
formed by qualified personnel only.
Children and unauthorized persons should not be
allowed near the installation of PV modules.
Use module for its intended function only.
Be sure that all other system components are compat-
ible, and they do not subject the module to mechani-
cal or electrical hazards.
Do not touch terminals while module is exposed to
light or during installation.