Bosch Appliances AE125 Water Heater User Manual


 
La temperatura del agua de salida también puede variar si se sobrepasa el caudal máximo
(consulte el Gráfico 1) o si cambia el voltaje de entrada.
Cada módulo calefactor está protegido por un disyuntor térmico electromecánico. Si la temperatura
de uno de los módulos calefactores sube demasiado, el disyuntor se disparará y cortará el
suministro eléctrico en dicho módulo calefactor. Si se dispara el disyuntor, debe ser reajustado por
un técnico de mantenimiento cualificado. Este disyuntor sólo se disparará en circunstancias
excepcionales.
La unidad AE115 se suministra con dos voltajes independientes, y la unidad AE125 se suministra
con tres voltajes independientes. La unidad puede seguir funcionando si se desconecta o si falla
uno de estos voltajes, pero el control de temperatura será deficiente (En Canadá, la unidad sólo
dispone de un suministro de voltaje).
Según el territorio del país, la temperatura del suministro de agua puede variar entre algo más de
4ºC en invierno y 21ºC en verano, con un promedio de 12,7ºC.
Diagrama 4: Diagrama de conexiones internas para una unidad monofásica AE125. (La unidad AE115
tiene dos módulos calefactores dos suministros). (En Canadá, durante la instalación se coloca un bloque
de terminales auxiliar).
CUTOUT
L2A
L2C
L2B
L1A
L1B
L1C
Wiring Diagram for AE125, 3 x 240V supply. PowerStar heater.
Thermistor
CUTOUT CUTOUT
Electronic PCB
Temperature
adjustment
potentiometer
MODULE A
Flow
transducer
Brass inlet manifold and Triac heat sink
For clarity
The positions of
terminals shown
here do not
correspond to
their positions on
the installer
terminal blocks
MODULE B
MODULE C
Especificaciones
Unidad AE115
Unidad AE125
Suministro de voltaje
2 x 240V CA (Canadá 240V
CA)
3 x 240V CA (Canadá 240V
CA)
Amperaje
2 x 40 A (Canadá 80 A)
3 x 40 A (Canadá 120 A)
Potencia máxima
17,25 kW
26,85kW
Intervalo de control de
temperatura
35°C a 55°C
35°C a 55°C
Intervalo de presión
15 psi hasta 150 psi
15 psi hasta 150 psi
Caudal mínimo
2,26 litros/min
3,02 litros/min
Caudal máximo
Véase el Gráfico 1, Página 8
Véase el Gráfico 1, Página 8
Dimensiones (sin acoplamientos
de agua)
39,3 cm alto x 38,7 cm ancho x
11,4 cm profundo
39,3 cm alto x 38,7 cm ancho x
11,4 cm profundo
Peso (sin agua)
9 kg
10 kg
Esquema eléctrico del AE125, 3 suministros de 240V, calentador PowerStar
PCI electrónica
Potenciómetro de
ajuste de
temperatura
Transductor
de caudal
Termistor
DISYUNTOR
DISYUNTOR
DISYUNTOR
MODULO
MODULO
MODULO
Colector de entrada de bronce y
disipador térmico Triac
Para una mayor
claridad, las
posiciones de los
terminales aquí
mostrados no se
corresponden con
sus posiciones en
los bloques de
terminales de
instalación.
9
WARNING
The unit must only be installed in the orientation shown in Diagram 1, i.e., mounted in a vertical position
with the water fittings located at the bottom of the unit.
Under no circumstances should the unit be
mounted differently.
If being used in a public place, position the unit out of easy reach to discourage vandalism.
Mount the unit onto a flat section of wall, well away from any potential splashes of water or spray.
Position the unit upright with all plumbing and electrical connections at the bottom of the unit.
Mounting on the wall
Undo the retaining screws on the front cover and take the cover off the unit. Hold the back plate in
position against the wall and mark the four mounting holes.
Drill the holes and secure the unit using the four wood screws supplied or an appropriate alternative
method.
Plumbing the unit
WARNING
Do not install a non-return check valve within 10 feet of the inlet. Do not apply heat or solder to
connections or pipes if they are already directly connected to the unit.
Fitting the pipes
The unit should be connected directly to the main cold water supply and not to pre-heated water.
(The inlet water temperature must not be greater than 86°F.) The unit should be installed with shut-
off valves on both the inlet and outlet connections.
It is recommended that you use ¾ inch or ½ inch copper or high-pressure flex connections.
Use Teflon tape for sealing pipe threads. Do NOT use pipe dope.
Remember to keep the hot water pipe runs as short as possible.
After the unit has been plumbed, and before you wire it, flush it with water to remove any debris or
loose particles. Failure to do so may make the unit inoperable.
Connecting the unit to the pipes
The inlet and outlet connections are clearly marked on the unit. They each have a ¾ inch NPT
connector.
Install a ball valve in the cold water line. This valve can be used to turn off the water supply to the
unit if it needs servicing, or to reduce the water flow if it is too high.
DISCLAIMER
As a condition of installing this product in the Commonwealth of Massachusetts a pressure relief valve
shall be installed on the cold water side, by a licensed plumber MGL 142 Section 19 Approval number:
P1-09-25
Wiring to the unit in the United States of America
WARNING
The unit must be installed by a qualified electrician, in accordance with the current version of the National
Electrical Code. The unit must be grounded.
4