Filter
Top Products
Congratulations on your purchase of the BOB Travel Bag. It is
designed to contain and protect your single seat BOB Sport Utility,
Revolution or Stroller Strides stroller during transport. The Travel Bag
may be rolled and guided by the end handle or carried via shoulder
strap and/or side handle. The Travel Bag will need to be assembled
prior to use.
Before attempting to assemble or use your new Travel Bag, read
and understand these instructions to ensure proper assembly
and operation. If you are unclear on any point, contact your dealer
or BOB before use.
WARNINGS
.
This product is designed exclusively for use with BOB single Sport
Utility, Revolution or Stroller Strides strollers. It is not intended for
use with any other strollers or products.
.
When not in use, keep out of reach of children.
.
Maximum Weight Capacity 30lb (13.6Kg) Do not overload.
.
Never leave child unattended.
.
The Travel Bag is designed to reduce the possibility of damage to
your stroller during transportation but does not eliminate it completely.
.
We recommend inspecting your Stroller and Travel Bag before and
after each transport journey to ensure functionality and safety.
Assembly Instructions:
A1. Remove bag from packaging. Place bag flat on ground or table
with wheels down. Open Travel Bag top cover zipper and locate
components. Fig. A identifies the anatomy and components of the
Travel Bag.
A2. Unfasten the Velcro of the five Fabric Flaps along inboard sides
of travel bag. Temporarily place top of each over side and out of the
way as shown in Fig. A.
A3. Locate wall support panel, (black plastic sheet) unroll and note
orientation of notch at each end.
A4. Orient wall support panel with notches toward top cover (up)
and feed each end into each respective pocket along inside corners
of Travel Bag as shown in Fig B. Push ends of wall support panel
fully into each pocket until notch is aligned with pocket seam.
A5. Align and fasten Velcro of fabric flaps straight and secure around
wall support panel. You may find it helpful to bend the support panel
top edge slightly inboard while the Velcro of each fabric flap is secured.
A6. Locate fork dropout
protector and confirm it is
attached securely to end of
small red webbing as shown
in Fig. C. The fork dropout
protector can be replaced
easily if lost or damaged with
most other common fork
dropout protector(s) used on
strollers and bicycles for
shipping, available through
your bicycle or stroller dealer.
Use Instructions:
U1. Prepare Travel Bag: Zip
Travel Bag zipper completely
open and fold top cover over,
exposing pockets for Front
Wheel and Front Wheel
Quick Release (QR). Locate
center strap and unfasten
side release buckle. Place
center strap ends outboard
of Travel Bag as shown in
Fig. 1.
U2. Prepare stroller to place
in Travel Bag. Remove
contents from stroller
(occupant and all contents of
Low Boy luggage pouch).
Remove stroller rear wheels.
Close rear wheel QRs. (See
Rear Wheel section of your
strollers owners manual).
U3. Remove Front Wheel
from stroller (See Front
Wheel section of your
strollers owners manual).
Remove Front QR from Front
Wheel. Reassemble Front
QR components in proper
orientation as shown in Fig.
2, and place inside the gray
pocket located inside top
cover of Travel Bag. Locate
black plastic axle protectors
at ends of red straps inside
large front wheel pocket.
Push hollow end of each
plastic axle protector fully
over each end of Front Wheel
axle as shown in Fig. 3.
Place Front Wheel into
pocket inside top cover and
fasten Velcro closures.
U4. Place rear wheels inside
Travel Bag with stub axles
facing up. Position stroller
wheels along center line as
far back towards base of bag
as possible, leaving extra
space for fork protector, as
shown in Fig. 4.
U5. For Sport Utility Stroller
(fixed wheel) models, close
Caliper Brake Quick Release
Lever after removing wheel,
as stroller will fold more
Fig. C: Fork Dropout Protector
shown properly attached.
Notch
Pocket Seam
Insert
Notch
fully up
to Seam
Fig. B: Panel ends into corner
pockets (right side shown).
Fig. 1: Travel Bag fully assembled
and prepared for stroller.
Center Strap
open w/ends
outboard
Top
Cover
Open
Fig. 2: Front QR anatomy
shown properly assembled.
Conical
Springs
Adjusting Nut
Cam Housing
QR
Lever
Rod
Fig. A: Anatomy of the BOB Travel Bag.
Handles
Shoulder
Strap
Wall Support Panel (rolled up)
Fork Protector
& Strap
Front
Wheel
Pocket
Zippered Top Cover
Front QR
Pocket
Fabric Flaps
(open)
Center Strap
& Buckle
P1
TRA
TRA
VEL b
VEL b
a
a
g INS
g INS
TR
TR
UCTIONS
UCTIONS
(800) 893-2447 www.bobgear.com email- info@bobgear.com Phone: (208) 375-5171
Fax: (208) 375-5172, BOB Trailers, Inc.
5475 Gage St. Boise, Idaho 83706
OMA17A