American Water Heater 319407-002 Water Heater User Manual


 
22
Operational Conditions
Condensation
Moisture from the products of combustion condenses on the
tank surface and the outside jacket of the water heater and
forms drops of water which may fall onto the burner or other
hot surfaces. This will produce a “sizzling” or “frying” noise.
NOTE: This condensation is normal and should not be
confused with a leaking tank. Condensation may increase or
decrease at different times of the year.
High efficient energy saver water heaters will produce
larger amounts of condensation on initial start-up or when
a large amount of hot water is being used. NOTE: Do not
confuse this with a “tank leak”. Once the water reaches a
temperature of 120°F and the tank warms up (usually 1-2
hours), the condensation will stop.
IMPORTANT: It is always recommended that a suitable
metal drain pan be installed under the water heater
to protect the area from water damage resulting from
normal condensation production, a leaking tank or piping
connections. Refer to “Location Requirements” on page
4. Under no circumstances is the manufacturer to be held
responsible for any water damage in connection with this
water heater.
Water Heater Sounds
During the normal operation of the water heater, sounds or
noises may be heard. These noises are common and may
result from the following:
1. Normal expansion and contraction of metal parts during
periods of heat-up and cool-down.
2. Condensation causes sizzling and popping within the
burner area and should be considered normal.
3. Sediment buildup in the tank bottom will create varying
amounts of noise and may cause premature tank failure.
Drain and flush the tank as directed under “Draining and
Flushing”.
Smoke/Odor
The water heater may give off a small amount of smoke
and odor during the initial start-up of the unit. This is due to
the burning off of oil from metal parts of a new unit and will
disappear after a few minutes of operation.
Safety Shut-off
This water heater is designed to automatically shut-off in the
event of the following:
1. The water temperature exceeds 189°F (87°C) for 160°F
models.
3. Excessive combustion chamber temperatures.
4. The presence of flammable vapors.
This unit is equipped with a flammable vapor sensor, designed
to shut off the gas supply in the event the heater has been
exposed to flammable vapors (spilled gasoline or paint fumes
for example). IMPORTANT: If the flammable vapor sensor
activates a qualified service person must be contacted to reset
the water heater. This unit is also equipped with a thermal
switch designed to shut off the gas control valve/thermostat
in the event the water heater has poor combustion caused
by a blocked vent or insufficient combustion air. If the switch
opens, check the flame-trap for signs of high temperature (blue
or black discoloration), and inspect your installation for any
problems with venting or combustion air (See Troubleshooting
Flowchart on page 29). Reset the thermal switch by depressing
the small button in the center of the switch.
IMPORTANT: Correct any issues prior to resetting the switch.
Contact the Product Service and Support Department
for service information at: 1-877-817-6750.
A temperature limit switch or ECO (Energy Cut Off) sensor
located in the gas control valve\thermostat, is used to shut off the
water heater if the water temperature exceeds 189°F (87°C).
The Diagnostic Status Light will flash a code indicating
an “Overheat Failure” (4 Flashes). See “Operating the
Temperature Control System.” If the gas control valve/
thermostat has an “ECO Lockout” the gas control valve/
thermostat must be replaced by a qualified person. Contact
your local dealer for service information.
Anode Rod/Water Odor
Each water heater contains at least one anode rod,
which will slowly deplete (due to electrolysis) prolonging
the life of the water heater by protecting the glass-lined
tank from corrosion. Adverse water quality, hotter water
temperatures, high hot water usage, hydronic heating
devices, and water softening methods can increase
the rate of anode rod depletion. Once the anode rod
is depleted, the tank will start to corrode, eventually
developing a leak.
Certain water conditions will cause a reaction between the
anode rod and the water. The most common complaint
associated with the anode rod is a “rotten egg smell”
produced from the presence of hydrogen sulfide gas
dissolved in the water.
IMPORTANT: Do not remove this rod permanently as it will
void any warranties. A special anode rod may be available
if water odor or discoloration occurs.
NOTE: This rod may reduce but not eliminate water odor
problems. The water supply system may require special
filtration equipment from a water conditioning company to
successfully eliminate all water odor problems.
Artificially softened water is exceedingly corrosive because
the process substitutes sodium ions for magnesium and
calcium ions. The use of a water softener may decrease
the life of the water heater tank.
The anode rod should be inspected after a maximum of
three years and annually thereafter until the condition of
the anode rod dictates its replacement.
NOTE: Artificially softened water requires the anode rod to
be inspected annually.
The following are typical (but not all) signs of a depleted
anode rod:
The majority of the rods diameter is less than 3/8”.
Significant sections of the support wire (approx. 1/3 or
more of the anode rod’s length) are visible.
If the anode rod show signs of either or both it should be
replaced. NOTE: Whether re-installing or replacing the anode
rod, check for any leaks and immediately correct if found.
In replacing the anode:
1. Turn off gas supply to the water heater.
2. Shut off the water supply and
open a nearby hot water faucet to
depressurize the water tank.
3. Drain approximately 5 gallons of
water from tank. (Refer to “Draining
and Flushing” for proper procedures).
Close drain valve.
4. Remove old anode rod.
5. Use Teflon® tape or approved pipe
sealant on threads and install new
anode rod.
6. Turn on water supply and open a
nearby hot water faucet to purge air
from water system.
7. Check for any leaks and immediately
correct any if found.
8. Restart the water heater as directed in this manual. See
the Repair Parts Illustration for anode rod location.
TEFLON
®
is a registered trademark of E.I. Du Pont De Nemours and Company.
Figure 25:
Anode Rod Depletion