American Standard SERIES 7193 Indoor Furnishings User Manual


  Open as PDF
of 4
 
LAKELAND™ KITCHEN SINKS
SERIES 7193
Installation
Instructions
791393-100 Rev. A
Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
BEFORE YOU BEGIN...
33"
(838mm)
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
COUNTERTOP CUTOUT FOR
NEW INSTALLATIONS
AMERICAST BRAND
SELF RIMMING
SINK
OUTLINE
CUTTING LINE
1" R (25mm) TYP.
Certified to comply with ANSI A112.19.4.M
U.S. Patent No. 4,664,982
Other patents pending.
CAN/C.S.A. B-45
Observe local plumbing and building codes.
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN
THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.
®
©AMERICAN STANDARD INC. 2005
™
Unpack new sink and inspect carefully for damage.
Replace the sink in its original packing carton to
protect it until you are ready to begin installation.
Refer to American Standard roughing-in information for
specific dimensions for each model.
Recommended Tools & Materials
Silicone Sealant
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Basin Wrench
Saber Saw
Tubing Cutter
Tape Measure
Hacksaw
Mineral Spirits
22"
(559mm)
5/8"
(16mm)
1-5/8" (16mm)
COUNTERTOP MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
33"
(838mm)
LAKELAND SINGLE BOWL
MODEL 7193 SELF RIMMING
COUNTERTOP CUTOUT FOR
REPLACEMENT INSTALLATIONS
SINK
OUTLINE
CUTTING LINE
1" R (25mm) TYP.
22"
(559mm)
5/8"
(16mm)
5/8" to 1-5/8"
(16 to 41mm)
CUTOUT DIMENSIONS FOR SINKS:
Below are the dimensions needed to determine the cutout size for your
installation. Select the correct diagram for your application and refer to the
instructions below.
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for the faucet supply lines and
the structural parts of the cabinet.
By using the diagrams below and measuring your sink, draw the outline of
the sink onto the countertop. This is not the cutting outline.
Refer to the diagram for your sink and draw a line the required distance in
from the sink outline. Cut on this line.
CAUTION:
1. Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")
2. Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after
the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.
NOTE: Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such
as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.
27-3/8"
(695mm)
COUNTERTOP CUTOUT FOR
UNDERCOUNTER INSTALLATIONS
2-5/16" R (19mm) TYP.
16-7/8"
(429mm)
CUTOUT
SUPPORT
CLIPS
SINK MOUNTED FAUCET
MODEL 7193 UNDER COUNTER MOUNT
LAKELAND SINGLE BOWL
29-1/2"
(749mm)
3/4" R (19mm) TYP.
20-1/2"
(521mm)
CUTOUT
SUPPORT
CLIPS
next