American Standard M968498 Indoor Furnishings User Manual


 
(In Toronto Area only: 1-905-3061093)
Innsbrook Lavatory Faucet
with SELECTRONIC™ Technology
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
605XTMV
6055.202
6055.205
PRODUCT No.s
6056.202
6056.205
6057.202
6057.205
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
© 2005 American Standard
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
M968498 Rev.1.2
Certified to comply with ASME A112.18.1M
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
MOUNTING
SURFACE
Roughing-in Dimensions
10'
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction 4" center to center mounting.
Operates on DC (battery) or AC permanent power. In-line
strainer for solenoid is integral. Single inlet 3/8 compression,
built-in checks, and flexible stainless steel 15" reach inlet
hose for spout connection.
INSTALL SPOUT ASSEMBLY;
Fig. 3
INSTALLATION
CAUTION
Turn off hot and cold water
supplies before beginning
1. Make sure PUTTY PLATE (1) is installed on
FAUCET BODY (2). Fig. 1a.
2. Insert WIRES (3), FLEX HOSE (4) and STUDS (5)
through holes of mounting surface. Fig. 1a.
3. From under side of mounting surface install SPIN
NUTS (6) onto MOUNTING STUDS (5). Fig. 1b.
4. Align FAUCET (2) and hand tighten SPIN NUTS (6)
to secure faucet to mounting surface. Fig. 1b.
Fig. 1a
1
2
114mm
(4-1/2)
508mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
125mm
(4-7/8)
81mm
(3-3/16)
175mm
(6-7/8)
162mm
(6-3/8)
155mm
(6-1/8)
102mm
(4)
35mm
(1-3/8)
DIA.
3 HOLES
38mm
(1-1/2)
MAX.
124mm
(4-7/8)
108mm
(4-1/4)
57mm
(2-1/4)
1
6
5
2
4
3
6
5
5
Fig. 1b
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 4a
4
5b. AC Power Supply (for 6056 series)
5c. 10 ft. Extension Wire (for 6057 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 6055 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c