American Standard 0490.027 Indoor Furnishings User Manual


  Open as PDF
of 2
 
J45
BARRIER FREE
© 2008 AS America Inc.
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 51mm (2") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
NOTES:
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE
TEMPLATE SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range
of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
FINISHED
WALL
OR
SPLASH BACK
486mm
(19-1/8)
184mm
(7-1/4)
83mm
(3-1/4)
203mm
(8)
OPTIONAL
FINISHED
FLOOR
318mm
(12-1/2)
1-1/4 O.D.
TAILPIECE
1-1/4 O.D.
WASTE
203mm
(8)
*
178mm
(7)
273mm
(10-3/4)
*
COUNTERTOP (BY OTHERS)
187mm
(7-3/8)
11mm
(7/16)
SEALING
COMPOUND
SUPPLIES
AS REQ'D.
C/L
787mm (31)
851mm (33-1/2)
851mm
(33-1/2)
102mm
(4)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARANCE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
RONDALYN™
COUNTERTOP SINK
VITREOUS CHINA
RONDALYN™ COUNTERTOP SINK
• Made from vitreous china
• Self-rimming with cutout template supplied
• Front overow
• Faucet ledge
Shown with 4801.862 Amarilis/Heritage faucet
with Triune cross handles (not included)
❏ 0490.011 Faucet holes on 8" (203mm) centers
(illustrated)
❏ 0491.019 Faucet holes on 4" (102mm) centers
❏ 0491.027 Faucet holes on 4" (102mm) centers
• Extra right-hand hole
❏ 0491.035 Faucet holes on 4" (102mm) centers
• Extra left-hand hole
❏ 0490.156 Center hole only
Nominal Dimensions:
486mm (19-1/8") Round
Bowl sizes:
381mm (15") wide
308mm (12-1/8") front to back
146mm (5-3/4") deep
Compliance Certications -
Meets or Exceeds the
Following Specications:
• ASME A112.19.2M for
Vitreous China Fixtures
Revised 2/08
SEE REVERSE FOR ADDITIONAL ROUGHING-IN
DIMENSIONS
To Be Specied:
❏ Color: ❏ White ❏ Bone
❏ Linen ❏ Silver
❏ Fawn Beige ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available