American Standard 0031.000 Indoor Furnishings User Manual


  Open as PDF
of 1
 
J3
BARRIER FREE
© 2008 AS America Inc.
TOWN SQUARE
®
27"
PEDESTAL SINK
FIRECLAY
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen
❏ Silver ❏ Black
❏ Town Square Faucet:
❏ Centerset Lavatory Faucet: 2555.201
❏ Widespread Lavatory Faucet: 2555.801
(shown)
❏ Other Lavatory Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
NOTES:
*
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM
FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.9M.
These measurements are subject to change or cancellation. No responsibility
is assumed for use of superseded or voided pages.
1-1/4" O.D.
WASTE
*
24"
(610mm)
*
22"
(559mm)
SUPPLIES AS
REQUIRED
6"
(152mm)
DRAIN
CHASE
OPEN
TO
FLOOR
9-5/8"
(244mm)
21-1/4"
(540mm)
27"
(686mm)
FINISHED WALL
FINISHED
FLOOR
1-3/4" DIA.
STD. DRAIN
OUTLET
4"
(102mm)
20-1/4" (514mm)
2-5/8"
(67mm)
4"
(102mm)
5/8"
(16mm)
PED BASE
OUTLINE
PED TOP
OUTLINE
36"
(914mm)
28"
(711mm)
3-3/4" (95mm)
8"
(203mm)
6"
(152mm)
10"
(254mm)
1-1/4" O.D.
TAILPIECE
3/8" (10mm) DIA.
BASE ANCHOR
SCREW HOLES
ON 6" (152mm)
CTRS
3/8" (10mm) DIA.
SLAB ANCHOR
SCREW HOLES
ON 20-1/4" (514mm)
CTRS
TOWN SQUARE
®
27" PEDESTAL SINK
• American classic design
• Clean straight lines with classic ogee curves
• Rear overow
• Supplied with mounting kit
• Design-matched to Town Square
®
xture and faucets
• Right Height™ for greater comfort during use
• Made from reclay
❏ 0780.400 Faucet holes on 4" (102mm) centers
❏ 0780.800 Faucet holes on 8" (203mm) centers
❏ 0780.100 Center hole only
Nominal Dimensions:
27" x 21-1/4" x 36"
(686 x 540 x 914mm)
Separate Components:
❏ 0780.004 Pedestal top 4" (102mm) centers
❏ 0780.008 Pedestal top 8" (203mm) centers
❏ 0780.001 Center hole only
❏ 0031.000 Pedestal only
Bowl sizes:
15" (381mm) wide
12-1/2 (318mm) front to back
6-1/2" (165mm) deep
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.9M for Non-Vitreous Ceramic Fixtures
• CAN/CSA B45 Series
Revised 2/08